K60P100M100SF2RM Datasheet, PDF (1692/1809 Pages) Freescale Semiconductor, Inc – K60 Sub-Family Reference Manual

Memory map/register definition
I2Sx_ISR field descriptions (continued)
Field
Description
This flag bit is set when RX1 or Rx FIFO 1 is loaded with a new value and two-channel mode is selected.
RDR1 is cleared when the core reads the RX1 register. If Rx FIFO 1 is enabled, RDR1 is cleared when
the FIFO is empty. If IER[RIE] and IER[RDR1EN] are set, a receive data 1 interrupt request is issued on
setting of RDR1 bit in case Rx FIFO1 is disabled, if the FIFO is enabled, the interrupt is issued on RFF1
assertion. The RDR1 bit is cleared by POR and I²S reset.
14
RDR0
0 No new data for core to read.
1 New data for core to read.
Receive Data Ready 0.
This flag bit is set when RX0 or Rx FIFO 0 is loaded with a new value. RDR0 is cleared when the core
reads the RX0 register. If Rx FIFO 0 is enabled, RDR0 is cleared when the FIFO is empty. If IER[RIE] and
IER[RDR0EN] are set, a receive data 0 interrupt request is issued on setting of RDR0 bit in case Rx
FIFO0 is disabled, if the FIFO is enabled, the interrupt is issued on RFF0 assertion. The RDR0 bit is
cleared by POR and I²S reset.
13
TDE1
0 No new data for core to read.
1 New data for core to read.
Transmit Data Register Empty 1.
This flag is set whenever data is transferred to TXSR from TX1 register and two-channel mode is
selected. If Tx FIFO1 is enabled, this occurs when there is at least one empty slot in TX1 or Tx FIFO1. If
Tx FIFO1 is not enabled, this occurs when the contents of TX1 are transferred to TXSR.
The TDE1 bit is cleared when the core writes to TX1. If IER[TIE] and IER[TDE1EN] are set, an I²S
transmit data 1 interrupt request is issued on setting of TDE1 bit. The TDE1 bit is cleared by POR and I²S
reset.
12
TDE0
0 Data available for transmission.
1 Data needs to be written by the core for transmission.
Transmit Data Register Empty 0.
This flag is set whenever data is transferred to TXSR from TX0 register. If Tx FIFO 0 is enabled, this
occurs when there is at least one empty slot in TX0 or Tx FIFO 0. If Tx FIFO 0 is not enabled, this occurs
when the contents of TX0 are transferred to TXSR. The TDE0 bit is cleared when the core writes to TX0.
If IER[TIE] and TIE[TDE0EN] are set, an I²S transmit data 0 interrupt request is issued on setting of TDE0
bit. The TDE0 bit is cleared by POR and I²S reset.
11
ROE1
0 Data available for transmission.
1 Data needs to be written by the core for transmission.
Receiver Overrun Error 1.
This flag is set when the RXSR is filled and ready to transfer to RX1 register or to Rx FIFO 1 (when
enabled) and these are already full and Two-Channel mode is selected. If Rx FIFO 1 is enabled, this is
indicated by RFF1 flag, else this is indicated by the RDR1 flag. The RXSR is not transferred in this case.
The ROE1 flag causes an interrupt if IER[RIE] and IER[ROE1EN] are set.
The ROE1 bit is cleared by POR and I²S reset. It is also cleared by writing `1' to this bit. Clearing the
CR[RE] bit does not affect the ROE1 bit.
10
ROE0
0 No overrun detected
1 Receiver overrun error occurred
Receiver Overrun Error 0.
Table continues on the next page...
1692
K60 Sub-Family Reference Manual, Rev. 6, Nov 2011
Freescale Semiconductor, Inc.