English
Language : 

SH7059 Datasheet, PDF (19/1042 Pages) Renesas Technology Corp – 32-Bit RISC Microcomputer
Differences between SH7058 and SH7058S/SH7059
SH7058 (Rev.3, REJ09B0046-0300H)
11.3.11 Event Count Function and Event Cycle
Measurement
Figure 11.25 Event Cycle Measurement Operation
SH7058S/SH7059
11.3.11 Event Count Function and Event Cycle
Measurement
Figure 11.25 Event Cycle Measurement Operation
Figure amended
Pφ
TCNT3
Clock
TCNT3 0000
Compare-match
trigger
(from channel 9)
GR3A
0001
0002
0003
0004
0005
0003
5678
5679
567A
567B
567C
567D
567E
567A
TSR3
IMF3A
Cleared by software
Pφ
TCNT3
Clock
TCNT3 0000
Compare-match
trigger
(from channel 9)
GR3A
0001
0002
0003
0004
0005
0004
5678
5679
567A
567B
567C
567D
567E
567A
TSR3
IMF3A
Cleared by software
11.6 Sample Setup Procedures
Figure 11.60 Sample Setup Procedure for PWM Timer
Operation (Channels 6 and 7)
408
2. Set the port B control register L (PBCRL) corresponding
to the waveform output port to ATU PWM output. Also set
the corresponding bit to 1 in the port B IO register (PBIOR)
to specify the output attribute.
11.7 Usage Notes
423
External Output Value in Software Standby Mode: In
software standby mode, the ATU register and external
output values are cleared to 0. However, while the channel
1, 2, and 11 TIO1A to TIO1H, TIO2A to TIO2H, TIO11A,
and TIO11B external output values are cleared to 0
immediately after software standby mode is exited, other
external output values and all registers are cleared to 0
immediately after a transition to software standby mode.
Also, when pin output is inverted by the pin function
controller's port B invert register (PBIR) or port K invert
register (PKIR), the corresponding pins are set to 1.
11.6 Sample Setup Procedures
Figure 11.60 Sample Setup Procedure for PWM Timer
Operation (Channels 6 and 7)
Description amended
2. Set the port B control register L (PBCRL) corresponding
to the waveform output port to ATU PWM output. .
11.7 Usage Notes
Title and description amended
External Output Values in Software Standby Mode and
Pin State after Software Standby Mode Release: In
software standby mode, the ATU register and external
output values are initialized. The pin state is high
impedance.
Since the settings of the pin function controller (PFC) are
initialized, the PFC must be set again to use the function of
the ATU-II external pins after software standby release.
Figure 11.74 External Output Value Transition Points in
Relation to Software Standby Mode
423
12.1.4 Register Configuration
Table 12.2 Advanced Pulse Controller Register
429
Note: Register access with an internal clock multiplication
ratio of 4 requires four or five internal clock (φ) cycles.
12.2.1 Pulse Output Port Control Register (POPCR)
430
POPCR is initialized to H'0000 by a power-on reset and in
hardware standby mode. It is not initialized in software
standby mode.
Figure 11.74 External Output Value Transition Points in
Relation to Software Standby Mode
Figure deleted
12.1.4 Register Configuration
Table 12.2 Advanced Pulse Controller Register
Note deleted
12.2.1 Pulse Output Port Control Register (POPCR)
Description amended
POPCR is initialized to H'0000 by a power-on reset, in
hardware standby mode and in software standby mode.
Rev.3.00 Mar. 12, 2008 Page xix of xc
REJ09B0177-0300