UPD78F1502AGK-GAK-AX Datasheet, PDF (894/1031 Pages) Renesas Technology Corp – 16-Bit Single-Chip Microcontrollers

78K0R/Lx3
CHAPTER 31 ELECTRICAL SPECIFICATIONS
Absolute Maximum Ratings (TA = 25°C) (2/3)
Parameter
Symbols
Conditions
Ratings
Unit
Output voltage
VO1
P00 to P02, P10 to P17, P30 to P34, P40, P41,
P50 to P57, P60, P61, P70 to P77, P80 to P87,
P90 to P97, P100 to P102, P120, P130, P140 to
P147
−0.3 to EVDD +0.3
V
VO2
P20 to P27, P150 to P152, P157
−0.3 to AVDD0 +0.3
V
VO3
P110, P111
−0.3 to AVDD1 +0.3
V
VO4
SEG0 to SEG53, COM0 External resistance
−0.3 to VDD +0.3^Note
V
to COM7
division method,
capacitor split method
Internal voltage boosting
−0.3 to VLC0 +0.3^Note
V
method
Analog input voltage VAI
ANI0 to ANI10, ANI15, AMP0+, AMP1+, AMP2+,
−0.3 to AVDD0 +0.3
V
AMP0-, AMP1-, AMP2- (μ PD78F150xA)
and −0.3 to VDD +0.3^Note
<R>
<R>
Analog output voltage VAO1
VAO2
Analog input reference AVREF
voltage
AVREFP
AVREFM
Output current, high
IOH1
IOH2
IOH3
ANI0 to ANI10, ANI15 (μ PD78F151xA)
−0.3 to AVDD +0.3
V
and −0.3 to VDD +0.3^Note
ANO0, ANO1
−0.3 to AVDD1 +0.3^Note
V
AMP0O, AMP1O, AMP2O
−0.3 to AVDD0 +0.3^Note
V
μ PD78F151xA
−0.3 to AVDD +0.3 ^Note
V
μ PD78F150xA
−0.3 to AVDD0 +0.3 ^Note
V
μ PD78F150xA
−0.3 to AVDD0 +0.3 ^Note
V
and AVREFM≤ AVREFP
Per pin
P00 to P02, P10-P17, P30 to P34,
−10
mA
P40, P41, P70 to P77, P80 to
P87, P120, P130
P50 to P57, P90 to P97,
P100 to P102, P140 to P147
−10
mA
Total of all pins P00 to P02, P10-P17, P30 to P34,
−25
mA
−50 mA
P40, P41, P70 to P77, P80 to
P87, P120, P130
P50 to P57, P90 to P97, P100 to
−25
mA
P102, P140 to P147
Per pin
P20 to P27, P150 to P152,
Total of all pins ^{P157, P110, P111}
−0.5
mA
−2
mA
Per pin
AMP0O, AMP1O, AMP2O
−1
mA
Total of all pins
−3
mA
Note Must be 6.5 V or lower.
Cautions 1. Product quality may suffer if the absolute maximum rating is exceeded even momentarily for any
parameter. That is, the absolute maximum ratings are rated values at which the product is on the
verge of suffering physical damage, and therefore the product must be used under conditions that
ensure that the absolute maximum ratings are not exceeded.
2. The value of the current that can be run per pin must satisfy the value of the current per pin and
the total value of the currents of all pins.
Remark Unless specified otherwise, the characteristics of alternate-function pins are the same as those of port pins.
R01UH0004EJ0501 Rev.5.01
878
Jun 20, 2011