M16C65 Datasheet, PDF (770/829 Pages) Renesas Technology Corp – RENESAS MCU M16C FAMILY / M16C/60

Under development
M16C/65 Group
Preliminary Specification
This is a preliminary specification and is subject to change.
30. Flash Memory
30.9.4 Standard Serial I/O Mode 1
In standard serial I/O mode 1, a serial programmer is connected to the MCU by using clock
synchronous serial I/O.
Table 30.19 lists Pin Functions (Flash Memory Standard Serial I/O Mode 1) and Table 30.20 lists
Setting of Standard Serial I/O Mode 1.
Figure 30.20 shows Circuit Application in Standard Serial I/O Mode 1. Control pins vary by programmer.
For more information, refer to the programmer manual.
Table 30.19 Pin Functions (Flash Memory Standard Serial I/O Mode 1)
Pin
VCC1, VCC2,
VSS
Name
Power input
I/O
Power
Supply
-
CNVSS
RESET
CNVSS
I
Reset input I
VCC1
VCC1
XIN
XOUT
Clock input I
Clock output O
VCC1
BYTE
AVCC, AVSS
VREF
P0_0 to P0_7
P1_0 to P1_7
P2_0 to P2_7
P3_0 to P3_7
P4_0 to P4_7
P5_1 to P5_4,
P5_6, P5_7
P5_0
P5_5
P6_0 to P6_3
P6_4 / RTS1
P6_5/CLK1
P6_6 / RXD1
P6_7 / TXD1
P7_0 to P7_7
P8_0 to P8_7
P9_0 to P9_7
P10_0 to P10_7
P11_0 to P11_7
P12_0 to P12_7
P13_0 to P13_7
P14_0 to P14_1
BYTE input I
Analog power
supply input
Reference I
voltage input
Input port P0 I
Input port P1 I
Input port P2 I
Input port P3 I
Input port P4 I
Input port P5 I
CE input
I
EPM input I
Input port P6 I
BUSY output O
SCLK input I
RXD input I
TXD output O
Input port P7 I
Input port P8 I
Input port P9 I
Input port P10 I
Input port P11 I
Input port P12 I
Input port P13 I
Input port P14 I
VCC1
VCC2
VCC2
VCC2
VCC2
VCC2
VCC2
VCC2
VCC2
VCC1
VCC1
VCC1
VCC1
VCC1
VCC1
VCC1
VCC1
VCC1
VCC1
VCC2
VCC2
VCC1
Description
Apply the flash program and erase voltage to the VCC1 pin,
and VCC2 to the VCC2 pin. The VCC application condition is
that VCC2 ≤ VCC1. Apply 0 V to the VSS pin.
Connect to the VCC1 pin.
Reset input pin. During td(OCOS), input a low-level signal to
the RESET pin.
Input a high-level signal to the XIN pin and open the XOUT pin
when a main clock is not used.
Connect a ceramic resonator or crystal oscillator between pins
XIN and XOUT when the main clock is used. To input an
externally generated clock, input it to the XIN pin and open the
XOUT pin.
Connect this pin to VSS or VCC1.
Connect AVCC to VCC1 and AVSS to VSS, respectively.
Reference voltage input pin for A/D converter.
Input a high- or low-level signal or leave open.
Input a high- or low-level signal or leave open.
Input a high- or low-level signal or leave open.
Input a high- or low-level signal or leave open.
Input a high- or low-level signal or leave open.
Input a high- or low-level signal or leave open.
Input a high-level signal.
Input a low-level signal.
Input a high- or low-level signal or leave open.
BUSY signal output pin
Serial clock input pin
Serial data input pin.
Serial data output pin.
Input a high- or low-level signal or leave open.
Input a high- or low-level signal or leave open.
Input a high- or low-level signal or leave open.
Input a high- or low-level signal or leave open.
Input a high- or low-level signal or leave open.
Input a high- or low-level signal or leave open.
Input a high- or low-level signal or leave open.
Input a high- or low-level signal or leave open.
REJ09B0484-0030 Rev.0.30 Sep 09, 2008
Page 735 of 791