M16C65 Datasheet, PDF (272/829 Pages) Renesas Technology Corp – RENESAS MCU M16C FAMILY / M16C/60

Under development
M16C/65 Group
Preliminary Specification
This is a preliminary specification and is subject to change.
14. Interrupts
Table 14.6 Relocatable Vector Tables (1/2)
Interrupt Source
Vector Address ⁽¹⁾
Address (L) to Address (H)
Software
Interrupt
Number
Reference
BRK instruction ⁽⁵⁾
- (Reserved)
+0 to +3 (0000h to 0003h)
0
1
M16C/60, M16C/20,
M16C/Tiny Series Software
Manual
INT7
+8 to +11 (0008h to 000Bh) 2
14.8 “INT Interrupt”
INT6
+12 to +15 (000Ch to 000Fh) 3
INT3
+16 to +19 (0010h to 0013h) 4
Timer B5
+20 to +23 (0014h to 0017h) 5
18. “Timer B”
Timer B4, UART1 start/stop condition +24 to +27 (0018h to 001Bh) 6
detection, bus collision detection ⁽⁴⁾
18. “Timer B”
Timer B3, UART0 start/stop condition +28 to +31 (001Ch to 001Fh) 7
detection, bus collision detection ⁽⁴⁾
23. “Serial Interface UARTi
(i = 0 to 2, 5 to 7)”
SI/O4, INT5 ⁽²⁾
+32 to +35 (0020h to 0023h) 8
14.8 “INT Interrupt”
SI/O3, INT4 ⁽²⁾
+36 to +39 (0024h to 0027h) 9
24. “Serial Interface SI/O3
and SI/O4”
UART2 start/stop condition
+40 to +43 (0028h to 002Bh) 10
detection, bus collision detection ⁽⁴⁾
23. “Serial Interface UARTi
(i = 0 to 2, 5 to 7)”
DMA0
+44 to +47 (002Ch to 002Fh) 11
16. “DMAC”
DMA1
+48 to +51 (0030h to 0033h) 12
Key input interrupt
+52 to +55 (0034h to 0037h) 13
14.10 “Key Input Interrupt”
A/D converter
+56 to +59 (0038h to 003Bh) 14
27. “A/D Converter”
UART2 transmit, NACK2 ⁽³⁾
+60 to +63 (003Ch to 003Fh) 15
23. “Serial Interface UARTi
(i = 0 to 2, 5 to 7)”
UART2 receive, ACK2 ⁽³⁾
+64 to +67 (0040h to 0043h) 16
UART0 transmit, NACK0 ⁽³⁾
+68 to +71 (0044h to 0047h) 17
UART0 receive, ACK0 ⁽³⁾
+72 to +75 (0048h to 004Bh) 18
UART1 transmit, NACK1 ⁽³⁾
+76 to +79 (004Ch to 004Fh) 19
UART1 receive, ACK1 ⁽³⁾
+80 to +83 (0050h to 0053h) 20
Timer A0
+84 to +87 (0054h to 0057h) 21
17. “Timer A”
Timer A1
+88 to +91 (0058h to 005Bh) 22
Timer A2
+92 to +95 (005Ch to 005Fh) 23
Timer A3
+96 to +99 (0060h to 0063h) 24
Timer A4
+100 to +103 (0064h to 0067h) 25
Timer B0
+104 to +107 (0068h to 006Bh) 26
18. “Timer B”
Timer B1
+108 to +111 (006Ch to 006Fh) 27
Timer B2
+112 to +115 (0070h to 0073h) 28
Notes:
1.
2.
3.
4.
5.
Address relative to address in INTB.
Use bits IFSR6 and IFSR7 in the IFSR register to select a source.
In I²C mode, NACK and ACK are interrupt sources.
Use bits IFSR26 and IFSR27 in the IFSR2A register to select a source.
These interrupts cannot be disabled using the I flag.
REJ09B0484-0030 Rev.0.30 Sep 09, 2008
Page 237 of 791