M16C65 Datasheet, PDF (273/829 Pages) Renesas Technology Corp – RENESAS MCU M16C FAMILY / M16C/60

Under development
M16C/65 Group
Preliminary Specification
This is a preliminary specification and is subject to change.
14. Interrupts
Table 14.7 Relocatable Vector Tables (2/2)
Interrupt Source
INT0
INT1
INT2
Vector Address ⁽¹⁾
Address (L) to Address (H)
+116 to +119 (0074h to 0077h)
+120 to +123 (0078h to 007Bh)
+124 to +127 (007Ch to 007Fh)
Software
Interrupt
Number
Reference
29
14.8 “INT Interrupt”
30
31
INT instruction interrupt ⁽³⁾
+128 to +131 (0080h to 0083h)
to
+160 to +163 (00A0h to 00A3h)
32 to 40
DMA2
+164 to +167 (00A4h to 00A7h)
41
DMA3
+168 to +171 (00A8h to 00ABh)
42
UART5 start/stop condition
+172 to +175 (00ACh to 0AFh)
43
detection, bus collision
detection, CEC1 ⁽⁴⁾
UART5 transmit, NACK5, CEC2 +176 to +179 (00B0h to 00B3h)
44
(2), (4)
UART5 receive, ACK5 ⁽²⁾
+180 to +183 (00B4h to 00B7h)
45
UART6 start/stop condition
+184 to +187 (00B8h to 00BBh)
46
detection, bus collision detection,
real-time clock cycle ⁽⁵⁾
UART6 transmit, NACK6,
+188 to +191 (00BCh to 00BFh)
47
real-time clock compare match ^{(2), (5)}
UART6 receive, ACK6 ⁽²⁾
+192 to +195 (00C0h to 00C3h)
48
UART7 start/stop condition
+196 to +199 (00C4h to 00C7h)
49
detection, bus collision
detection, remote control 0 ⁽⁶⁾
UART7 transmit, NACK7,
remote control 1 ^{(2), (6)}
+200 to +203 (00C8h to 00CBh)
50
UART7 receive, ACK7 ⁽²⁾
+204 to +207 (00CCh to 00CFh)
51
- (Reserved)
52 to 58
I²C-bus interface interrupt ^{(7) +236 to +239 (00ECh to 00EFh)}
59
SCL/SDA interrupt ⁽⁷⁾
+240 to +243 (00F0h to 00F3h)
60
- (Reserved)
61 to 63
Notes:
1.
2.
3.
4.
5.
6.
7.
Address relative to address in INTB.
In I²C mode, NACK and ACK are the interrupt sources.
These interrupts cannot be disabled using the I flag.
Use bits IFSR33 and IFSR34 in the IFSR3 register to select a source.
Use bits IFSR35 and IFSR36 in the IFSR3 register to select a source.
Use bits IFSR24 and IFSR25 in the IFSR2 register to select a source.
Use bits IFSR22 and IFSR23 in the IFSR2 register to select a source.
M16C/60, M16C/20,
M16C/Tiny Series
Software Manuall
16. “DMAC”
23. “Serial Interface
UARTi (i = 0 to 2, 5 to
7)”
26. “Consumer
Electronics Control
(CEC) Function”
20. “Real-Time Clock”
23. “Serial Interface
UARTi (i = 0 to 2, 5 to
7)”
22. “Remote Control
Signal Receiver”
23. “Serial Interface
UARTi (i = 0 to 2, 5 to
7)”
25. “Multi-Master I²C-
bus Interface”
REJ09B0484-0030 Rev.0.30 Sep 09, 2008
Page 238 of 791