HC4GX15 Datasheet, PDF (635/668 Pages) Altera Corporation – HardCopy IV Device Handbook

Chapter 1: DC and Switching Characteristics of HardCopy IV Devices
1–5
Electrical Characteristics
Table 1–4. HardCopy IV Device Recommended Operating Conditions—Preliminary (Part 2 of 2)
Symbol
Description
Condition
Minimum Typical
tR AM P
Power supply ramp time
Normal POR
(PORSEL = 1)
0.05
—
Fast POR
(PORSEL = 1) 0.05
—
(3)
Notes to Table 1–4:
(1) HardCopy IV devices do not require Programmable Power Technology.
(2) In HardCopy IV devices, this power supply is not used.
(3) If the PORSEL pin is connected to VCC, all supplies must ramp up within 4 ms.
Maximum Unit
100
ms
4
ms
Table 1–5 shows the transceiver power supply recommended operating conditions.
Table 1–5. HardCopy IV GX Transceiver Power Supply Recommended Operating Conditions
Symbol
Description
Minimum Typical Maximum Unit
V_{CCA_L}
V_{CCA_R}
V_{CCHIP_L} (1)
V_{CCHIP_R} (1)
V_{CCR_ L}
V_{CCR_ R}
V_{CCT_L}
V_{CCT_R}
V_{CCL_GXBLn} (2)
V_{CCL_GXBRn} (2)
V_{CCH_GXBLn} (2)
V_{CCH_GXBRn} (2)
Transceiver high voltage power (left side)
Transceiver high voltage power (right side)
Transceiver hard IP digital power (right side)
Transceiver hard IP digital power (left side)
Receiver power (left side)
Receiver power (right side)
Transmitter power (left side)
Transmitter power (right side)
Transceiver clock power (left side)
Transceiver clock power (right side)
Transmitter output buffer power (left side)
Transmitter output buffer power (right side)
2.85/2.375
3.0/2.5
(3)
3.15/2.625
V
V
V
0.87
0.90
0.93
V
V
1.05
1.1
1.15
V
V
1.05
1.1
1.15
V
V
1.05
1.1
2.35
V
1.33/1.425
1.4/1.5
(4)
1.47/1.575
V
V
Notes to Table 1–5:
(1) If V_{CCHIP_L/R} is connected to the same power supply source as Vcc, the recommended minimum and maximum operating supply levels are
0.87 V and 0.93 V respectively.
(2) The V_CCH and V_CCL powers are per transceiver block
(3) V_{CCA_L/R} must be connected to a 3.0 V supply if the CMU PLL, receiver CDR, or both are configured at a base data rate > 4.25Gbps. For data
rates up to 4.25 Gbps, you can connect V_{CCA_L/R} to either 3.0 V or 2.5 V.
(4) For data rates up to 6.5 Gbps, you can connect V_{CCH_GXBL/R} to either 1.4 V or 1.5 V.
DC Characteristics
This section lists the supply current, I/O pin leakage current, input pin capacitance,
on-chip termination (OCT) tolerance, and hot socketing specifications.
Supply Current
Standby current is the current the device draws after the device is configured, with no
inputs or outputs toggling and no activity in the device. Because these currents vary
largely with the resources you use, use the Excel-based PowerPlay Early Power
Estimator (EPE) to get supply current estimates for your design.
© June 2009 Altera Corporation
HardCopy IV Device Handbook Volume 4