|
82801CA Datasheet, PDF (56/521 Pages) Intel Corporation – I/O Controller Hub 3-S (ICH3-S) | |||
|
◁ |
Power Planes and Pin States
3.2
Integrated Pull-Ups and Pull-Downs
Table 3-2. Integrated Pull-Up and Pull-Down Resistors
Signal
EE_DIN
EE_DOUT
GNT[B:A]# / GNT[5]# / GPIO[17:16]
LAD[3:0]# / FWH[3:0]#
LDRQ[1:0]
PME#
PWRBTN#
SPKR
AC_BIT_CLK
AC_SDIN[1:0]
AC_SDOUT
AC_SYNC
LAN_RXD[2:0]
PDD[7] / SDD[7]
PDDREQ / SDDREQ
DPRSLPVR
LAN_CLK
USB[5:0][P:N]
Resistor Type
pull-up
pull-up
pull-up
pull-up
pull-up
pull-up
pull-up
pull-down
pull-down
pull-down
pull-down
pull-down
pull-up
pull-down
pull-down
pull-down
pull-down
pull-down
Nominal Value
24 kâ¦
24 kâ¦
24 kâ¦
24 kâ¦
24 kâ¦
24 kâ¦
24 kâ¦
24 kâ¦
20 kâ¦
20 kâ¦
20 kâ¦
20 kâ¦
9 kâ¦
5.9 kâ¦
5.9 kâ¦
20 kâ¦
1 Mâ¦
15 kâ¦
Notes
1
1
1
1
1
1
1
1, 5
2, 6
2
2, 6
2, 5
3
4
4
2
NOTES:
1. Simulation data shows that these resistor values can range from 18 k⦠to 42 kâ¦.
2. Simulation data shows that these resistor values can range from 13 k⦠to 38 kâ¦.
3. Simulation data shows that these resistor values can range from 6 k⦠to 14 kâ¦.
4. Simulation data shows that these resistor values can range from 4.3 k⦠to 20 kâ¦.
5. The pull-up or pull-down on this signal is only enabled at boot/reset for strapping function.
6. This pull-down is enabled when either the ACLINK Shut Off bit in the AC â97 Global Control Register is set or
when both function 5 and function 6 of Dev 31 are hidden (disabled).
3.3
IDE Integrated Series Termination Resistors
Table 3-3 shows the ICH3 IDE signals that have integrated series termination resistors.
Table 3-3. IDE Series Termination Resistors
Signal
PDD[15:0], SDD[15:0, PDIOW#,
SDIOW#, PDIOR#, PDIOW#,
PDREQ, SDREQ, PDDACK#,
SDDACK#, PIORDY, SIORDY,
PDA[2:0], SDA[2:0], PDCS1#,
SDCS1#, PDCS3#, SDCS3#,
IRQ14, IRQ15
Integrated Series Termination Resistor Value
approximately 33 ⦠(See Note)
NOTE: Simulation data indicates that the integrated series termination resistors are a nominal 33 ⦠but can
range from 31 ⦠to 43 â¦.
3-56
Intel® 82801CA ICH3-S Datasheet
|
▷ |