SH7641 Datasheet, PDF (198/1036 Pages) Renesas Technology Corp – Renesas 32-Bit RISC Microcomputer SuperH™ RISC engine Family / SH7641 Series

Section 4 Clock Pulse Generator (CPG)
PLL frequency
Clock FRQCR
multiplier
operating register _PLL
PLL
mode setting Circuit 1 Circuit 2
Ratio of internal
clock frequencies
(I:B:P)
Input clock
Selectable frequency ranges (MHz)
Output clock
(CKIO pin) Internal clock Bus clock
Peripheral clock
6
H'1303 ON (×4) ON (×2) 8:2:2
10 to 12.5
20 to 25
80 to 100
20 to 25
20 to 25
H'1313 ON (×4) ON (×2) 4:2:2
10 to 16.66 20 to 33.33 40 to 66.66 20 to 33.33 20 to 33.33
H'1333 ON (×4) ON (×2) 2:2:2
10 to 16.66 20 to 33.33 20 to 33.33 20 to 33.33 20 to 33.33
7
H'1000 ON (×1) OFF
1:1:1
20 to 33.33 20 to 33.33 20 to 33.33 20 to 33.33 20 to 33.33
H'1001 ON (×1) OFF
1:1:1/2
20 to 50
20 to 50
20 to 50
20 to 50
10 to 25
H'1002 ON (×1) OFF
1:1:1/3
20 to 50
20 to 50
20 to 50
20 to 50
6.66 to 16.66
H'1003 ON (×1) OFF
1:1:1/4
20 to 50
20 to 50
20 to 50
20 to 50
5 to 12.5
H'1101 ON (×2) OFF
2:1:1
20 to 33.33 20 to 33.33 40 to 66.66 20 to 33.33 20 to 33.33
H'1103 ON (×2) OFF
2:1:1/2
20 to 50
20 to 50
40 to 100
20 to 50
10 to 25
H'1111 ON (×2) OFF
1:1:1
20 to 33.33 20 to 33.33 20 to 33.33 20 to 33.33 20 to 33.33
H'1113 ON (×2) OFF
1:1:1/2
20 to 50
20 to 50
20 to 50
20 to 50
10 to 25
H'1202 ON (×3) OFF
3:1:1
26.66 to 33.33 26.66 to 33.33 80 to 100
26.66 to 33.33 26.66 to 33.33
H'1222 ON (×3) OFF
1:1:1
26.66 to 33.33 26.66 to 33.33 26.66 to 33.33 26.66 to 33.33 26.66 to 33.33
H'1303 ON (×4) OFF
4:1:1
20 to 25
20 to 25
80 to 100
20 to 25
20 to 25
H'1313 ON (×4) OFF
2:1:1
20 to 33.33 20 to 33.33 40 to 66.66 20 to 33.33 20 to 33.33
H'1333 ON (×4) OFF
1:1:1
20 to 33.33 20 to 33.33 20 to 33.33 20 to 33.33 20 to 33.33
Notes: 1. The ratio of clock frequencies, where the input clock frequency is assumed to be 1.
2. In modes 2 and 6, the frequency of the clock input from the EXTAL pin or the
frequency of the crystal resonator. In mode 7, the frequency of the clock input from
the CKIO pin.
Caution:
1. The frequency of the internal clock is the frequency of the signal input to the CKIO
pin after multiplication by the frequency-multiplier of PLL circuit 1 and division by the
divider's divisor. Do not set a frequency for the internal clock below the frequency of
the signal on the CKIO pin.
2. The frequency of the peripheral clock is the frequency of the signal input to the CKIO
pin after multiplication by the frequency-multiplier of PLL circuit 1 and division by the
divider's divisor. Set the frequency of the peripheral clock to 33.33 MHz or below. In
addition, do not set a higher frequency for the internal clock than the frequency on
the CKIO pin.
3. The frequency multiplier of the PLL circuit can be selected as x1, x2, x3 or x4. The
divisor of the divider can be selected as x1, x1/2, x1/3 or x1/4. The settings are made
in the respective frequency-control registers.
4. The signal output by PLL circuit 1 is the signal on the CKIO pin multiplied by the
frequency multiplier of PLL circuit 1. Ensure that the frequency of the signal from PLL
circuit 1 is no more than 100 MHz.
Rev. 4.00 Sep. 14, 2005 Page 148 of 982
REJ09B0023-0400