EP4SE360F35I4 Datasheet, PDF (240/432 Pages) Altera Corporation – This section provides a complete overview of all features relating to the Stratix IV device family, which is the most architecturlly advanced

7–16
Chapter 7: External Memory Interfaces in Stratix IV Devices
Memory Interfaces Pin Support
Figure 7–11. Number of DQS/DQ Groups per Bank in EP4SGX180 and EP4SGX230 Devices in the 1517-Pin FineLine BGA
Package ⁽¹⁾, ⁽²⁾, ⁽³⁾, ⁽⁴⁾, ⁽⁵⁾
DLL0
I/O Bank 1A
48 User I/Os
x4=7
x8/x9=3
x16/x18=1
I/O Bank 1C
42 User I/Os
x4=6
x8/x9=3
x16/x18=1
I/O Bank 2C
42 User I/Os
x4=6
x8/x9=3
x16/x18=1
I/O Bank 2A
48 User I/Os
x4=7
x8/x9=3
x16/x18=1
DLL1
I/O Bank 8A
40 User I/Os
x4=6
x8/x9=3
x16/x18=1
I/O Bank 3A
40 User I/Os
x4=6
x8/x9=3
x16/x18=1
I/O Bank 8B
24 User I/Os
x4=4
x8/x9=2
x16/x18=1
I/O Bank 8C
32 User I/Os
x4=3
x8/x9=1
x16/x18=0
I/O Bank 7C
32 User I/Os
x4=3
x8/x9=1
x16//x18=0
I/O Bank 7B
24 User I/Os
x4=4
x8/x9=2
x16/x18=1
EP4SGX180 and EP4SGX230 Devices
in the 1517-Pin FineLine BGA
I/O Bank 3B
24 User I/Os
x4=4
x8/x9=2
x16/x18=1
I/O Bank 3C
32 User I/Os
x4=3
x8/x9=1
x16/x18=0
I/O Bank 4C
32 User I/Os
x4=3
x8/x9=1
x16/x18=0
I/O Bank 4B
24 User I/Os
x4=4
x8/x9=2
x16/x18=1
I/O Bank 7A
40 User I/Os
x4=6
x8/x9=3
x16/x18=1
I/O Bank 4A
40 User I/Os
x4=6
x8/x9=3
x16/x18=1
DLL3
I/O Bank 6A
48 User I/Os
x4=7
x8/x9=3
x6/x18=1
I/O Bank 6C
42 User I/Os
x4=6
x8/x9=3
x16/x18=1
I/O Bank 5C
42 User I/Os
x4=6
x8/x9=3
x16/x18=1
I/O Bank 5A
48 User I/Os
x4=7
x8/x9=3
x6/x18=1
DLL2
Notes to Figure 7–11:
(1) These numbers are preliminary until the devices are available.
(2) EP4SGX180 and EP4SGX230 devices do not support ×32/×36 mode. To interface with a ×36 QDR II+/QDR II SRAM device, refer to “Combining
×16/×18 DQS/DQ Groups for a ×36 QDR II+/QDR II SRAM Interface” on page 7–26.
(3) You can also use DQS/DQSn pins in some of the ×4 groups as R_UP and R_DN pins, but you cannot use a ×4 group for memory interfaces if two pins
of the ×4 group are used as R_UP and R_DN pins for OCT calibration. If two pins of a ×4 group are used as R_UP and R_DN pins for OCT calibration, you
can use the ×16/×18 or ×32/×36 groups that include that ×4 group, however there are restrictions on using ×8/×9 groups that include that ×4
group.
(4) All I/O pin counts include dedicated clock inputs that you can use for data inputs.
(5) You can also use some of the DQS/DQ pins in I/O Bank 1C as configuration pins. You cannot use a ×4 DQS/DQ group with any of its pin members
used for configuration purposes. Ensure that the DQS/DQ groups that you have chosen are not also used for configuration because you may lose
up to four ×4 DQS/DQ groups, depending on your configuration scheme.
Stratix IV Device Handbook
Volume 1
February 2011 Altera Corporation