|
82801BA Datasheet, PDF (54/498 Pages) Intel Corporation – Intel 82801BA I/O Controller Hub 2 (ICH2) and Intel 82801BAM I/O Controller Hub 2 Mobile | |||
|
◁ |
Power Planes and Pin States
Table 3-2. Integrated Pull-Up and Pull-Down Resistors (Continued)
Signal
AC_SDIN[0]
AC_SDIN[1]
AC_SDOUT
AC_SYNC
LAN_RXD[2:0]
PDD[7] / SDD[7]
PDDREQ / SDDREQ
Resistor Type
pull-down
pull-down
pull-down
pull-down
pull-up
pull-down
pull-down
Nominal Value
20 Kâ¦
20 Kâ¦
20 Kâ¦
20 Kâ¦
9 Kâ¦
5.9 Kâ¦
5.9 Kâ¦
Notes
2, 6
2, 6
2, 6
2, 6
3
4
4
NOTES:
1. Simulation data shows that these resistor values can range from 18 K⦠to 42 Kâ¦.
2. Simulation data shows that these resistor values can range from 13 K⦠to 38 Kâ¦.
3. Simulation data shows that these resistor values can range from 6 K⦠to 14 Kâ¦.
4. Simulation data shows that these resistor values can range from 4.3 K⦠to 20 Kâ¦.
5. The pull-up or pull-down on this signal is only enabled at boot/reset for strapping function.
6. This pull-down is only enabled when the ACLINK Shut Off bit in the ACâ97 Global Control Register is set to 1.
3.3
IDE Integrated Series Termination Resistors
Table 3-3 shows the ICH2 IDE signals that have integrated series termination resistors.
Table 3-3. IDE Series Termination Resistors
Signal
Integrated Series Termination Resistor Value
PDD[15:0], SDD[15:0], PDIOW#, SDIOW#,
PDIOR#, PDIOW#, PDREQ, SDREQ,
PDDACK#, SDDACK#, PIORDY, SIORDY,
PDA[2:0], SDA[2:0], PDCS1#, SDCS1#,
PDCS3#, SDCS3#, IRQ14, IRQ15
approximately 33 ⦠(See Note)
NOTE: Simulation data indicates that the integrated series termination resistors are a nominal 33 ⦠but can
range from 31 ⦠to 43 â¦.
3.4
Output and I/O Signals Planes and States
Table 3-4 shows the power plane associated with the output and I/O signals, as well as the state at
various times. Within the table, the following terms are used:
âHigh-Zâ
Tri-state. ICH2 not driving the signal high or low.
âHighâ
ICH2 is driving the signal to a logic â1â
âLowâ
ICH2 is driving the signal to a logic â0â
âDefinedâ
Driven to a level that is defined by the function (will be high or low)
âUndefinedâ
ICH2 is driving the signal, but the value is indeterminate.
âRunningâ
Clock is toggling or signal is transitioning because function not stopping
âOffâ
The power plane is off, so ICH2 is not driving
Note that the signal levels are the same in S4 and S5.
3-2
82801BA ICH2 and 82801BAM ICH2-M Datasheet
|
▷ |