MC9S12G Datasheet, PDF (1084/1160 Pages) Freescale Semiconductor, Inc – Ignores external trigger. Performs one conversion sequence and stops.

Electrical Characteristics
Table A-7. 5-V I/O Characteristics
ALL 5V RANGE I/O PARAMETERS ARE SUBJECT TO CHANGE FOLLOWING CHARACTERIZATION
Conditions are 4.5 V < V_DD35 < 5.5 V junction temperature from –40°C to +150°C, unless otherwise noted
I/O Characteristics for all I/O pins except EXTAL, XTAL,TEST and supply pins.
Num C
Rating
Symbol
Min
Typ
Max
Unit
1 P Input high voltage
2 T Input high voltage
V_IH
0.65*V_DD35
—
V_IH
—
—
—
V
V_DD35+0.3
V
3 P Input low voltage
V_IL
—
—
0.35*V_DD35 V
4 T Input low voltage
V_IL
V_SSRX–0.3
—
—
V
5 C Input hysteresis
VHYS 0.06V*V_DD35
—
0.3V*V_DD35 mV
6
Input leakage current (pins in high impedance input
mode)¹ Vin = VDD35 or VSS35
I_in
P M temperature range
-1
—
V temperature range
-0.5
—
C temperature range
-0.4
—
µA
1
0.5
0.4
7 C Input leakage current (pins in high impedance input
mode)¹ Vin = VDD35 or VSS35
I_in
27°C
µA
1
8 P Output high voltage (pins in output mode)
IOH = –4 mA
V_OH
V_DD35 – 0.8
—
—
V
9 P Output low voltage (pins in output mode)
IOL = +4mA
V_OL
—
—
0.8
V
10 P Internal pull up current
V_IH min > input voltage > V_IL max
I_PUL
-10
—
-130
µA
11 P Internal pull down current
V_IH min > input voltage > V_IL max
I_PDH
10
—
130
µA
12 D Input capacitance
C_in
—
7
13 T Injection current²
—
Single pin limit
I_ICS
–2.5
Total device Limit, sum of all injected currents
I_ICP
–25
14 P Port J, P, AD interrupt input pulse filtered (STOP)³
t_{P_MASK}
—
—
15 P Port J, P, AD interrupt input pulse passed (STOP)³
t_{P_PASS}
10
—
—
pF
mA
2.5
25
3
µs
—
µs
16 D Port J, P, AD interrupt input pulse filtered (STOP) in n_{P_MASK}
—
—
3
number of bus clock cycles of period 1/f_bus
17 D Port J, P, AD interrupt input pulse passed (STOP) in n_{P_PASS}
4
number of bus clock cycles of period 1/f_bus
—
—
18 D IRQ pulse width, edge-sensitive mode (STOP) in
n_IRQ
1
number of bus clock cycles of period 1/f_bus
—
—
1 _{Maximum leakage current occurs at maximum operating temperature. Current decreases by approximately one-half for each}
8°C to 12 C° in the temperature range from 50°C to 125°C.
2 _{Refer to Section A.1.4, “Current Injection” for more details}
3 _{Parameter only applies in stop or pseudo stop mode.}
MC9S12G Family Reference Manual, Rev.1.01
1084
Freescale Semiconductor
This document is valid for the S12G96 and the S12G128 device. All information related to other devices is preliminary.