C8051F960-B-GM Datasheet, PDF (188/492 Pages) Silicon Laboratories – Ultra Low Power 128K, LCD MCU Family

C8051F96x
14.5. AES Block Cipher Decryption
14.5.1. AES Block Cipher Decryption using DMA
Normally, the AES block is used with the DMA. This provides the best performance and lowest power con-
sumption. Code examples are provided in 8051 compiler independent C code using the DMA. It is highly
recommended to use with the code examples. The steps are documented in the datasheet for complete-
ness.
 Prepare decryption key and data to be decryption in xram.
 Reset AES module by clearing bit 2 of AES0BCFG.
 sable the first three DMA channels by clearing bits 0 to 2 in the DMA0EN sfr.
 Configure the first DMA channel for the AES0KIN sfr
Select the first DMA channel by writing 0x00 to the DMA0SEL sfr
Configure the first DMA channel to move xram to AES0KIN sfr by writing 0x05 to the DMA0NCF sfr
Write 0x01 to DMA0NMD to enable wrapping
Write the xram location of decryption key to the DMA0NBAH and DMA0NBAL sfrs.
Write the key length in bytes to DMA0NSZL sfr
Clear the DMA0NSZH sfr
Clear the DMA0NAOH and DMA0NAOL sfrs.
 Configure the second DMA channel for the AES0BIN sfr.
Select the second DMA channel by writing 0x01 to the DMA0SEL sfr.
Configure the second DMA channel to move xram to AES0BIN sfr by writing 0x06 to the DMA0NCF sfr.
Clear DMA0NMD to disable wrapping.
Write the xram address of the data to be decrypted to the DMA0NBAH and DMA0NBAL sfrs.
Write the number of bytes to be decrypted in multiples of 16 bytes to the DMA0NSZH and DMA0NSZL sfrs.
Clear the DMA0NAOH and DMA0NAOL sfrs.
 Configure the third DMA channel for the AES0YOUT sfr
Select the third DMA channel by writing 0x02 to the DMA0SEL sfr
Configure the third DMA channel to move the contents of the AES0YOUT sfr to xram by writing 0x08 to the
DMA0NCF sfr
Enable transfer complete interrupt by setting bit 7 of DMA0NCF sfr
Clear DMA0NMD to disable wrapping
Write the xram address for decrypted data to the DMA0NBAH and DMA0NBAL sfrs.
Write the number of bytes to be decrypted in multiples of 16 bytes to the DMA0NSZH and DMA0NSZL sfrs.
Clear the DMA0NSZH sfr
Clear the DMA0NAOH and DMA0NAOL sfrs.
 Clear first three DMA interrupts by clearing bits 0 to 2 in the DMA0INT sfr.
 Enable first three DMA channels setting bits 0 to 2 in the DMA0EN sfr
 Configure the AES Module data flow for AES Block Cipher by writing 0x00 to the AES0DCFG sfr.
 Write key size to bits 1 and 0 of the AES0BCFG
 Configure the AES core for decryption by clearing bit 2 of AES0BCFG
 Initiate the encryption operation be setting bit 3 of AES0BCFG
 Wait on the DMA interrupt from DMA channel 2
 Disable the AES Module by clearing bit 2 of AES0BCFG
 Disable the DMA by writing 0x00 to DMA0EN
188
Rev. 1.0