HD64F38024HV Datasheet, PDF (38/684 Pages) Renesas Technology Corp – Hardware Manual Renesas 8-Bit Single-Chip Microcomputer H8 Family/H8/300L Super Low Power Series

Section 1 Overview
Table 1.3 Bonding Pad Coordinates of HCD64F38024, HCD64F38024R
Pad No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Pad Name
PB7/AN7
AVCC
P13/TMIG
P14/IRQ4/ADTRG
P16
P17/IRQ3/TMIF
X1
X2
AVSS
VSS
OSC2
OSC1
TEST
RES
P50/WKP0/SEG1
P51/WKP1/SEG2
P52/WKP2/SEG3
P53/WKP3/SEG4
P54/WKP4/SEG5
P55/WKP5/SEG6
P56/WKP6/SEG7
P57/WKP7/SEG8
P60/SEG9
P61/SEG10
P62/SEG11
P63/SEG12
P64/SEG13
P65/SEG14
P66/SEG15
P67/SEG16
P70/SEG17
P71/SEG18
P72/SEG19
P73/SEG20
P74/SEG21
P75/SEG22
P76/SEG23
P77/SEG24
P80/SEG25
P81/SEG26
P82/SEG27
Coordinates
X (μm) Y (μm)
–1802 1904
–1802 1717
–1802 1443
–1802 1292
–1802 1157
–1802 1022
–1802 887
–1802 753
–1802 638
–1802 473
–1802 318
–1802 202
–1802 69
–1802 –63
–1802 –195
–1802 –355
–1802 –514
–1802 –674
–1802 –844
–1802 –1008
–1802 –1348
–1802 –1709
–1802 –1904
–1686 –1999
–1198 –1999
–1057 –1999
–916
–1999
–755
–1999
–625
–1999
–493
–1999
–352
–1999
–202
–1999
–69
–1999
72
–1999
213
–1999
330
–1999
459
–1999
583
–1999
730
–1999
937
–1999
1686
–1999
Pad No.
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
Pad Name
P83/SEG28
P84/SEG29
P85/SEG30
P86/SEG31
P87/SEG32
PA3/COM4
PA2/COM3
PA1/COM2
PA0/COM1
V3
V2
V1
VCC
VSS
P90/PWM1
P91/PWM2
P92
P93
P94
P95
IRQAEC
P30/UD
P31/TMOFL
P32/TMOFH
P33
P34
P35
P36/AEVH
P37/AEVL
P40/SCK32
P41/RXD32
P42/TXD32
P43/IRQ0
PB0/AN0
PB1/AN1
PB2/AN2
PB3/AN3/IRQ1/TMIC
PB4/AN4
PB5/AN5
PB6/AN6
Coordinates
X (μm) Y (μm)
1802
–1898
1802
–1750
1802
–1594
1802
–1454
1802
–1296
1802
–1182
1802
–1068
1802
–954
1802
–840
1802
–726
1802
–534
1802
–402
1802
–267
1802
–126
1802
206
1802
457
1802
707
1802
958
1802
1209
1802
1460
1802
1710
1802
1904
1686
1999
1222
1999
1077
1999
932
1999
788
1999
643
1999
498
1999
353
1999
226
1999
63
1999
–82
1999
–229
1999
–404
1999
–577
1999
–751
1999
–925
1999
–1099 1999
–1686 1999
Note:
VSS Pads (No. 9 and 10) should be connected to power supply lines.
TEST Pad (No. 13) should be connected to VSS.
If the pad of these aren’t connected to the power supply line, the LSI will not operate correctly. These values show the
coordinates of the centers of pads. The accuracy is ±5 μm. The home-point position is the chip’s center and the center
is located at half the distance between the upper and lower pads and left and right pads.
Rev. 8.00 Mar. 09, 2010 Page 16 of 658
REJ09B0042-0800