XRT72L56 Datasheet, PDF (361/486 Pages) Exar Corporation – SIX CHANNEL DS3/E3 FRAMER IC WITH HDLC CONTROLLER

áç
PRELIMINARY
XRT72L56
SIX CHANNEL DS3/E3 FRAMER IC WITH HDLC CONTROLLER
REV. P1.1.2
the RxE3 Interrupt Enable Register - 1, as indicated
below.
RXE3 INTERRUPT ENABLE REGISTER - 1 (ADDRESS = 0X12)
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
Not Used
COFA
Interrupt
Enable
OOF
Interrupt
Enable
LOF
Interrupt
Enable
RO
RO
RO
R/W
R/W
R/W
0
0
0
0
X
0
BIT 1
LOS
Interrupt
Enable
R/W
X
BIT 0
AIS
Interrupt
Enable
R/W
0
Setting this bit-field to “1” enables this interrupt. Con-
versely, setting this bit-field to “0” disables this inter-
rupt.
Servicing the Change in Receive OOF Condition
Interrupt
Whenever the XRT72L56 Framer IC detects this in-
terrupt, it will do all of the following.
• It will assert the Interrupt Request output pin (INT),
by driving it “Low”.
• It will set Bit 3 (OOF Interrupt Status), within the Rx
E3 Interrupt Status Register - 1 to “1”, as indicated
below.
RXE3 INTERRUPT STATUS REGISTER - 1 (ADDRESS = 0X14)
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Not Used
COFA
Interrupt
Status
OOF
Interrupt
Status
LOF
Interrupt
Status
LOS
Interrupt
Status
AIS
Interrupt
Status
RO
RO
RO
RUR
RUR
RUR
RUR
RUR
0
0
0
0
1
0
0
0
Whenever the user’s system encounters the Change
in Receive OOF Condition Interrupt, then it should do
the following.
1. It should determine the current state of the OOF
condition. Recall, that this interrupt can be gen-
erated, whenever the XRT72L56 Framer IC
declares or clears the OOF defect. Hence, the
user can determine the current state of the LOS
defect by reading the state of Bit 5 (RxOOF)
within the Rx E3 Configuration and Status Regis-
ter - 2, as illustrated below.
RXE3 CONFIGURATION & STATUS REGISTER 2 (ADDRESS = 0X11)
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
RxLOF Algo RxLOF
RxOOF
RxLOS
RxAIS
RxPld Unstab
Rx
TMark
RxFERF
R/W
RO
RO
RO
RO
RO
RO
RO
X
X
X
X
X
X
X
X
If the OOF state is TRUE
1. It should transmit a FERF (Far-End-Receive Fail-
ure) indicator to the Remote Terminal Equipment.
Please see Section 4.2.4.2.1.3 on how to config-
ure the XRT72L56 to transmit the FERF indicator
to the Remote Terminal Equipment.
If the OOF state is FALSE
1. It should cease transmitting the FERF indication
to the Remote Terminal Equipment. Please see
Section 4.2.4.2.1.3 on how to control the state of
the “A” bit, which is transmitted via each out-
bound E3 frame.
342