XRT72L56 Datasheet, PDF (132/486 Pages) Exar Corporation – SIX CHANNEL DS3/E3 FRAMER IC WITH HDLC CONTROLLER

XRT72L56 SIX CHANNEL DS3/E3 FRAMER IC WITH HDLC CONTROLLER
REV. P1.1.2
áç
PRELIMINARY
TXE3 TTB-5 REGISTER (ADDRESS = 0X3D)
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
TxTTB-5[7:0]
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
BIT 2
R/W
0
BIT 1
R/W
0
BIT 0
R/W
0
This Read/Write byte-field, along with the Tx TTB-0
through Tx TTB-4 and Tx TTB-6 through Tx TTB-15
registers allows a user to define a Trail Access Point
Identifier sequence of bytes, that will be transmitted to
the Remote Terminal. The Remote Receiving Termi-
nal will use this sequence of bytes to verify that it is
connected to the proper Transmitting Terminal. The
Transmit DS3/E3 Framer block will take the contents
of these 16 registers, and insert them into the TR byte
of the outbound E3 frame. In the sixth of a set of 16
E3 Frames, the Transmit DS3/E3 Framer block will
read in the contents of this register, and insert it into
the TR byte-field, within the very next outbound E3
frame.
The contents of this register, along with Tx TTB-1
through Tx TTB-4 and Tx TTB-6 through Tx TTB-15
are used to transmit 15 ASCII characters required for
the E.164 numbering format.
2.4.6.13 Transmit E3 TTB-6 Register (E3, ITU-T
G.832)
TXE3 TTB-6 REGISTER (ADDRESS = 0X3E)
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
TxTTB-6[7:0]
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
This Read/Write byte-field, along with the Tx TTB-0
through Tx TTB-5 and Tx TTB-7 through Tx TTB-15
registers permit a user to define a Trail Access Point
Identifier sequence of bytes, that will be transmitted to
the Remote Terminal. The Remote Receiving Termi-
nal will use this sequence of bytes to verify that it is
connected to the proper Transmitting Terminal. The
Transmit DS3/E3 Framer block will take the contents
of these 16 registers, and insert them into the TR byte
of the outbound E3 frame. In the seventh of a set of
16 E3 Frames, the Transmit DS3/E3 Framer block will
read in the contents of this register, and insert it into
the TR byte-field, within the very next outbound E3
frame.
The contents of this register, along with Tx TTB-1
through Tx TTB-5 and Tx TTB-7 through Tx TTB-15
are used to transmit 15 ASCII characters required for
the E.164 numbering format.
2.4.6.14 Transmit E3 TTB-7 Register (E3, ITU-T
G.832)
TXE3 TTB-7 REGISTER (ADDRESS = 0X3F)
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
TxTTB-7[7:0]
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
This Read/Write byte-field, along with the Tx TTB-0
through Tx TTB-6 and Tx TTB-8 through Tx TTB-15
registers allows a user to define a Trail Access Point
Identifier sequence of bytes, that will be transmitted to
the Remote Terminal. The Remote Receiving Termi-
nal will use this sequence of bytes to verify that it is
connected to the proper Transmitting Terminal. The
Transmit DS3/E3 Framer block will take the contents
of these 16 registers, and insert them into the TR byte
of the outbound E3 frame. In the eighth of a set of 16
113