XRT74L73 Datasheet, PDF (280/488 Pages) Exar Corporation – 3 CHANNEL, ATM UNI/PPP DS3/E3 FRAMING CONTROLLER

XRT74L73
3 CHANNEL, ATM UNI/PPP DS3/E3 FRAMING CONTROLLER
REV. P1.0.1
PRELIMINARY
(FERF Interrupt Enable) within the RxDS3 Interrupt
Enable Register, as illustrated below.
RXDS3 INTERRUPT ENABLE REGISTER (ADDRESS = 0X12)
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
CP Bit Error
Interrupt
Enable
LOS
Interrupt
Enable
AIS
Interrupt
Enable
Idle Interrupt
Enable
FERF
Interrupt
Enable
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
BIT 2
AIC
Interrupt
Enable
R/W
0
BIT 1
OOF
Interrupt
Enable
R/W
0
BIT 0
P-Bit Error
Interrupt
Enable
R/W
0
Setting this bit-field to “1” enables this interrupt. Con-
versely, setting this bit-field to “0” disables this inter-
rupt.
Servicing the Change of State on Receive FERF
Interrupt
Whenever the XRT74L73 Framer IC detects this in-
terrupt, it will do all of the following.
• It will assert the Interrupt Request Output pin (INT)
by driving it "High".
• It will set Bit 3 (FERF Interrupt Status), within the
Rx DS3 Interrupt Status Register, to “1”, as indi-
cated below.
RXDS3 INTERRUPT STATUS REGISTER (ADDRESS = 0X13)
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
CP-Bit Error
Interrupt
Status
LOS
Interrupt
Status
AIS
Interrupt
Status
Idle Interrupt
Status
FERF
Interrupt
Status
AIC
Interrupt
Status
OOF
Interrupt
Status
P-Bit Error
Interrupt
Status
RUR
RUR
RUR
RUR
RUR
RUR
RUR
RUR
0
0
0
0
1
0
0
0
Whenever the Terminal Equipment encounters a
Change in FERF Condition on Receive Interrupt, it
should do the following.
1. It should determine the current state of the FERF
condition. Recall, that this interrupt can gener-
RXDS3 STATUS REGISTER (ADDRESS = 0X11)
BIT 7
BIT 6
BIT 5
BIT 4
Reserved
RxFERF
RO
RO
RO
RO
0
0
0
0
ated, whenever the XRT74L73 Framer declares
or clears the FERF condition. Hence, to deter-
mine the current state of the FERF condition read
the state of Bit 4 (RxFERF), within the RxDS3
Status Registers, as illustrated below
BIT 3
RxAIC
RO
0
BIT 2
RO
0
BIT 1
RxFEBE[2:0]
RO
0
BIT 0
RO
0
4.3.6.2.6 The Change of State of Receive AIC
Interrupt
If the Change of State of Receive AIC Interrupt is en-
abled, then the XRT74L73 Framer IC will generate an
interrupt, anytime the Receive DS3 Framer block has
detected a change in the value of the AIC bit, within
the incoming DS3 data stream.
Enabling and Disabling the Change of State of
Receive AIC Interrupt:
To enable or disable the Change of State on Receive
AIC Interrupt, write the appropriate value into Bit 2
281