UPSD3354DV-40U6 Datasheet, PDF (249/272 Pages) STMicroelectronics – fast 8032 MCU with programmable logic

UPSD33xx
DC and AC parameters
Table 166. Preliminary MCU module DC characteristics
Symbol
Parameter
Test conditions
Min. Typ. Max. Unit
V_CC,
AV_CC
V_IH
Supply voltage⁽¹⁾
High level input voltage
(Ports 1, 3, 4, MCUAD0-7, MCUA8-11, XTAL1,
RESET)
5 V tolerant - max voltage 5.5 V
3.0 V < V_CC < 3.6 V
3.0
0.7V_CC
3.6
V
5.5⁽²⁾
V
Low level input voltage
V_{IL (Ports 1, 3, 4, MCUAD0-7, MCUA8-11, XTAL1,} 3.0 V < V_CC < 3.6 V V_SS – 0.5
RESET)
0.3V_CC V
V_OL1 Output low voltage (Port 4)
I_OL = 10 mA
0.6
V
V_OL2 Output low voltage (Other Ports)
I_OL =5 mA
0.6
V
V_OH1 Output high voltage (Ports 4 push-pull)
I_OH = –10 mA
2.4
V
V_OH2 Output high voltage (Port 0 push-pull)
I_OH = –5 mA
2.4
V
t(s) ^VOH3
Output high voltage (Other Ports Bi-directional
mode)
I_OH = –20 µA
2.4
V
uc ^{VOP XTAL open bias voltage (XTAL1, XTAL2)}
d _{IRST RESET pin pull-up current (RESET)}
Pro I_FR XTAL feedback resistor current (XTAL1)
te _IIHL1
ole ^IIHL2
s _IILL
t(s) ^{- Ob IPD(3)}
Input high leakage current (Port 0)
Input high leakage current (Port 1, 2, 3, 4)
Input low leakage current (Port 1, 2, 3, 4)
Power-down mode
Active - 12 MHz
Idle - 12 MHz
I_OL = 3.2 mA
1.0
2.0
V
V_IN = VSS
–10
–55 µA
XTAL1 = V_CC;
XTAL2 = V_SS
–20
50 µA
V_SS < V_IN < 5.5 V
–10
10 µA
V_IH = 2.3 V
–10
10 µA
V_IL < 0.5 V
–10
10 µA
V_CC = 3.6 V
65 95 µA
V_CC = 3.6 V
14 20 mA
10 12 mA
c _ICC-CPU Active - 24 MHz
du ^{(4)(5)(6) Idle - 24 MHz}
V_CC = 3.6 V
19 30 mA
13 17 mA
ro Active - 40 MHz
P _{Idle - 40 MHz}
V_CC = 3.6 V
26 40 mA
17 22 mA
te _{1. Power supply (VCC , AVCC) is always 3.0 to 3.6V for the MCU module. VDD for the PSD module may be 3V or 5 V.}
le _{2. Port 1 is not 5 V tolerant; maximum VIH = VCC + 0.5}
so 3. I_PD (Power-down mode) is measured with: XTAL1 = V_SS; XTAL2 = NC; RESET = V_CC; Port 0 = V_CC; all other pins are
b^{disconnected.}
O^{4. I}CC-CPU ^{(Active mode) is measured with: XTAL1 driven with t}CLCH^{, t}CHCL ^{= 5ns, V}IL ^{= V}SS ^{+ 0.5 V, V}IH ^{= V}CC ^{– 0.5 V,}
XTAL2 = NC; RESET = V_SS; Port 0 = V_CC; all other pins are disconnected. I_CC would be slightly higher if a crystal oscillator
is used (approximately 1 mA).
5. I_CC-CPU (Idle mode) is measured with: XTAL1 driven with t_CLCH, t_CHCL = 5ns, V_IL = V_SS + 0.5 V, V_IH = V_CC – 0.5 V, XTAL2
= NC; RESET = V_CC; Port 0 = V_CC; all other pins are disconnected. I_CC would be slightly higher if a crystal oscillator is used
(approximately 1 mA). All IP clocks are disabled.
6. I/O current = 0 mA, all I/O pins are disconnected.
Doc ID 9685 Rev 7
249/272