UPSD33XX Datasheet, PDF (207/231 Pages) STMicroelectronics – Fast 8032 MCU with Programmable Logic

uPSD33xx
Table 129. Preliminary MCU Module DC Characteristics
Symbol
Parameter
Test Conditions
Min.
Typ.
Max. Unit
V_{CC Supply Voltage}⁽¹⁾
3.0
3.6
V
High Level Input Voltage
V_IH
(Ports 0, 1, 2, 3, 4, XTAL1,
RESET)
5V Tolerant - max voltage 5.5V
3.0V < V_CC < 3.6V
0.7V_CC
5.5
V
Low Level Input Voltage
V_IL (Ports 0, 1, 2, 3, 4, XTAL1,
RESET)
3.0V < V_CC < 3.6V
V_SS – 0.5
0.3V_CC
V
V_OL1 Output Low Voltage (Port 4)
I_OL = 10mA
0.6
V
V
V_OL2
Output Low Voltage
(Other Ports)
I_OL =5mA
0.6
V
V
V_OH1
Output High Voltage
(Ports 4 push-pull)
I_OH = –10mA
2.4
V
V
V_OH2
Output High Voltage
(Port 0 push-pull)
I_OH = –5mA
2.4
V
V
V_OH3
Output High Voltage
(Other Ports Bi-directional mode)
I_OH = –20µA
2.4
V
V
V_OP
XTAL Open Bias Voltage
(XTAL1, XTAL2)
I_OL = 3.2mA
1.0
2.0
V
I_RST
RESET Pin Pull-up Current
(RESET)
V_IN = V_SS
–10
–55
uA
I_FR
XTAL Feedback Resistor Current
(XTAL1)
XTAL1 = V_CC; XTAL2 = V_SS
–20
50
uA
I_IHL1
Input High Leakage Current
(Port 0)
V_SS < V_IN < 5.5V
–10
10
uA
I_IHL2
Input High Leakage Current
(Port 1, 2, 3, 4)
V_IH = 2.3V
–10
10
uA
I_ILL
Input Low Leakage Current
(Port 1, 2, 3, 4)
V_IL < 0.5V
–10
10
uA
I_PD
(Note 2)
Power-down Mode
V_CC = 3.6V
65
95
uA
Active - 12MHz
I_CC-CPU
(Note
3,4,5)
Idle - 12MHz
Active - 24MHz
Idle - 24MHz
Active - 40MHz
Idle - 40MHz
V_CC = 3.6V
V_CC = 3.6V
V_CC = 3.6V
14
20
mA
10
12
mA
19
30
mA
13
17
mA
26
40
mA
17
22
mA
Note: 1. Power supply (V_CC) is always 3.0 to 3.6V for the MCU Module. V_DD for the PSD Module may be 3V or 5V.
2. I_PD (Power-down Mode) is measured with: XTAL1 = V_SS; XTAL2 = NC; RESET = V_CC; Port 0 = V_CC; all other pins are disconnected.
3. I_CC-CPU (Active Mode) is measured with: XTAL1 driven with t_CLCH, t_CHCL = 5ns, V_IL = V_SS + 0.5V, V_IH = V_CC – 0.5V, XTAL2 = NC;
RESET = V_SS; Port 0 = V_CC; all other pins are disconnected. I_CC would be slightly higher if a crystal oscillator is used (approximately
1mA).
4. I_CC-CPU (Idle Mode) is measured with: XTAL1 driven with t_CLCH, t_CHCL = 5ns, V_IL = V_SS + 0.5V, V_IH = V_CC – 0.5V, XTAL2 = NC;
RESET = VCC; Port 0 = VCC; all other pins are disconnected. ICC would be slightly higher if a crystal oscillator is used (approximately
1mA). All IP clocks are disabled.
5. I/O current = 0mA, all I/O pins are disconnected.
207/231