M1AFS600-PQ208 Datasheet, PDF (253/334 Pages) Microsemi Corporation – Fusion Family of Mixed Signal FPGAs

Fusion Family of Mixed Signal FPGAs
Table 3-2 • Recommended Operating Conditions¹
Symbol
Parameter²
Commercial
Industrial Units
T_J
VCC
Junction temperature
1.5 V DC core supply voltage
0 to +85
–40 to +100
°C
1.425 to 1.575 1.425 to 1.575 V
VJTAG
VPUMP
JTAG DC voltage
Programming voltage
1.4 to 3.6
1.4 to 3.6
V
Programming mode³ 3.15 to 3.45
3.15 to 3.45
V
Operation⁴
0 to 3.6
0 to 3.6
V
VCCPLL Analog power supply (PLL)
1.425 to 1.575 1.425 to 1.575 V
VCCI
1.5 V DC supply voltage
1.425 to 1.575 1.425 to 1.575 V
1.8 V DC supply voltage
1.7 to 1.9
1.7 to 1.9
V
2.5 V DC supply voltage
2.3 to 2.7
2.3 to 2.7
V
3.3 V DC supply voltage
3.0 to 3.6
3.0 to 3.6
V
LVDS differential I/O
2.375 to 2.625 2.375 to 2.625 V
LVPECL differential I/O
3.0 to 3.6
3.0 to 3.6
V
VCC33A +3.3 V power supply
2.97 to 3.63
2.97 to 3.63
V
VCC33PMP +3.3 V power supply
2.97 to 3.63
2.97 to 3.63
V
VAREF
Voltage reference for ADC
VCC15A ⁵ Digital power supply for the analog system
2.527 to 2.593 2.527 to 2.593 V
1.425 to 1.575 1.425 to 1.575 V
VCCNVM Embedded flash power supply
1.425 to 1.575 1.425 to 1.575 V
VCCOSC
AV, AC ⁶
Oscillator power supply
Unpowered, ADC reset asserted or unconfigured
2.97 to 3.63
2.97 to 3.63
V
–10.5 to 12.0
–10.5 to 11.6
V
Analog input (+16 V to +2 V prescaler range)
–0.3 to 12.0
–0.3 to 11.6
V
Analog input (+1 V to + 0.125 V prescaler range)
–0.3 to 3.6
–0.3 to 3.6
V
Analog input (–16 V to –2 V prescaler range)
–10.5 to 0.3
–10.5 to 0.3
V
Analog input (–1 V to –0.125 V prescaler range)
–3.6 to 0.3
–3.6 to 0.3
V
Analog input (direct input to ADC)
–0.3 to 3.6
–0.3 to 3.6
V
AG ⁶
Digital input
Unpowered, ADC reset asserted or unconfigured
–0.3 to 12.0
–0.3 to 11.6
V
–10.5 to 12.0
–10.5 to 11.6
V
Low Current Mode (1 µA, 3 µA, 10 µA, 30 µA)
–0.3 to 12.0
–0.3 to 11.6
V
Low Current Mode (–1 µA, –3 µA, –10 µA, –30 µA)
–10.5 to 0.3
–10.5 to 0.3
V
High Current Mode ⁷
–10.5 to 12.0
–10.5 to 11.6
V
AT ⁶
Unpowered, ADC reset asserted or unconfigured
–0.3 to 15.5
–0.3 to 14.5
V
Analog input (+16 V, +4 V prescaler range)
–0.3 to 15.5
–0.3 to 14.5
V
Analog input (direct input to ADC)
–0.3 to 3.6
–0.3 to 3.6
V
Digital input
–0.3 to 15.5
–0.3 to 14.5
V
Notes:
1. The ranges given here are for power supplies only. The recommended input voltage ranges specific to each I/O
standard are given in Table 2-85 on page 2-160.
2. All parameters representing voltages are measured with respect to GND unless otherwise specified.
3. The programming temperature range supported is T_ambient = 0°C to 85°C.
4. VPUMP can be left floating during normal operation (not programming mode).
5. Violating the V_CC15A recommended voltage supply during an embedded flash program cycle can corrupt the page being
programmed.
6. The input voltage may overshoot by up to 500 mV above the Recommended Maximum (150 mV in Direct mode),
provided the duration of the overshoot is less than 50% of the operating lifetime of the device.
7. The AG pad should also conform to the limits as specified in Table 2-48 on page 2-117.
Revision 4
3-3