M16C6NK Datasheet, PDF (331/404 Pages) Renesas Technology Corp – 16-BIT SINGLE-CHIP MICROCOMPUTER M16C FAMILY / M16C/60 SERIES

Under development
This document is under development and its contents are subject to change.
M16C/6N Group (M16C/6NK, M16C/6NM)
22. Electric Characteristics (Normal-ver.)
Table 22.28 Electrical Characteristics ⁽¹⁾
VCC = 3.3V
Symbol
Parameter
Measuring Condition
Standard
Min. Typ. Max.
Unit
VOH HIGH Output P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, IOH = –1mA
Voltage
P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7,
VCC-0.5
VCC
V
P6_0 to P6_7, P7_0, P7_2 to P7_7, P8_0 to P8_4,
P8_6, P8_7, P9_0, P9_2 to P9_7, P10_0 to P10_7,
P11_0 to P11_7,P12_0 to P12_7, P13_0 to P13_7,
P14_0, P14_1
VOH HIGH Output XOUT HIGHPOWER
Voltage
LOWPOWER
IOH = –0.1mA
IOH = –50µA
VCC-0.5
VCC-0.5
VCC
V
VCC
HIGH Output XCOUT HIGHPOWER
Voltage
LOWPOWER
With no load applied
2.5
V
With no load applied
1.6
VOL
LOW Output P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, IOL = 1mA
Voltage
P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7,
0.5 V
P6_0 to P6_7, P7_0 to P7_7, P8_0 to P8_4,
P8_6, P8_7, P9_0 to P9_7, P10_0 to P10_7,
P11_0 to P11_7,P12_0 to P12_7, P13_0 to P13_7,
P14_0, P14_1
VOL
LOW Output ^{XOUT HIGHPOWER}
Voltage
LOWPOWER
IOL = 0.1mA
IOL = 50µA
0.5 V
0.5
LOW Output ^{XCOUT HIGHPOWER}
With no load applied
0
V
Voltage
VT+-VT- ^Hysteresis
LOWPOWER
With no load applied
0
_________ _______
HOLD, RDY, TA0IN to TA4IN, TB0IN to TB5IN,
0.2
0.8 V
________ ________ _______ _____________ _________ _________
INT0 to INT5, NMI, ADTRG, CTS0 to CTS2,
SCL0 to SCL2, SDA0 to SDA2, CLK0 to CLK3,
_____
_____
TA0OUT to TA4OUT, KI0 to KI3,
VT+-VT- ^Hysteresis
VT+-VT- ^Hysteresis
IIH
HIGH Input
Current
RXD0 to RXD2, SIN3
_____________
RESET
XIN
P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, _{VI = 3.3V}
P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7,
0.2
1.8 V
0.2
0.8 ^V
4.0 ^µA
P6_0 to P6_7, P7_0 to P7_7, P8_0 to P8_7,
P9_0 to P9_7, P10_0 to P10_7,
P11_0 to P11_7, P12_0 to P12_7,
P13_0 to P13_7, P14_0, P14_1,
____________
XIN, RESET, CNVSS, BYTE
IIL
LOW Input
P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, _{VI = 0V}
Current
P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7,
–4.0 µA
P6_0 to P6_7, P7_0 to P7_7, P8_0 to P8_7,
P9_0 to P9_7, P10_0 to P10_7,
P11_0 to P11_7, P12_0 to P12_7,
P13_0 to P13_7, P14_0, P14_1,
____________
XIN, RESET, CNVSS, BYTE
RPULLUP Pull-up
Resistance
P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, _{VI = 0V}
P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7,
50 100 500 kΩ
P6_0 to P6_7, P7_0, P7_2 to P7_7, P8_0 to
P8_4, P8_6, P8_7, P9_0, P9_2 to P9_7,
P10_0 to P10_7, P11_0 to P11_7,
P12_0 to P12_7, P13_0 to P13_7,
P14_0, P14_1
RfXIN Feedback Resistance XIN
3.0
MΩ
RfXCIN Feedback Resistance XCIN
25
MΩ
VRAM RAM Retention Voltage
NOTES:
At stop mode
2.0
V
1. Referenced to VCC = 3.0 to 3.6V, VSS = 0V at Topr = –40 to 85°C, f(BCLK) = 24MHz unless otherwise specified.
________
________
2. P11 to P14, INT6 to INT8, CLK5, CLK6, SIN5 and SIN6 are only in the 128-pin version.
Rev.2.00 Nov 28, 2005 page 313 of 378
REJ09B0124-0200