M306H7MG-XXXFP Datasheet, PDF (264/329 Pages) Renesas Technology Corp – SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with DATA ACQUISITION CONTROLLER

M306H7MG-XXXFP/MC-XXXFP/FGFP
16. ELECTRICAL CHARACTERISTICS
Table 16.2 Recommended Operating Conditions (Note 1)
Symbol
Parameter
VCC1, VCC2 Supply voltage (VCC1 ≤ VCC2)
AVcc
Analog supply voltage
VDD2
Analog supply voltage
Vss
Supply voltage
AVss
Analog supply voltage
HIGH input
voltage
P31 to P37, P40 to P47, P50 to P57
P00 to P07, P10 to P17, P20 to P27, P30
Min.
2.0
0.8VCC2
0.8VCC2
Standard
Typ.
5.0
V CC2
V CC2
0
0
Max.
5.5
V CC2
V CC2
Unit
V
V
V
V
V
V
V
VIH
P60 to P67, P72 to P77, P80 to P84
P85 to P87, P90 to P97
XIN, RESET, CNVSS, M1, STARTB
0.8VCC1
0.8VCC2
V CC1
V
V CC2
V
VIL
VCVIN
LOW input
voltage
P70, P71
P31 to P37, P40 to P47, P50 to P57
P00 to P07, P10 to P17, P20 to P27, P30
P60 to P67, P70 to P77, P80 to P84
P85 to P87, P90 to P97,
XIN, RESET, CNVSS, M1, STARTB
Composite video input voltage CVIN, SYNCIN
0.8VCC1
0
0
0
5.75
V
0.2VCC2
V
0.2VCC2
V
0.2VCC1
V
0
0.2VCC2
V
2VP-P
V
I OH (peak)
I OH (avg)
HIGH peak output
current (Note2, Note3)
HIGH average
output current
P00 to P07,P10 to P17, P20 to P27,P30 to P37,
P40 to P47,P50 to P57, P60 to P67,P72 to P77,
P80 to P84,P86,P87,P90 to P97
P00 to P07,P10 to P17, P20 to P27,P30 to P37,
P40 to P47,P50 to P57, P60 to P67,P72 to P77,
P80 to P84,P86,P87,P90 to P97
- 10.0
mA
- 5.0
mA
I OL (peak)
LOW peak
output current
P00 to P07,P10 to P17, P20 to P27,P30 to P37,
P40 to P47, P50 to P57, P60 to P67,P70 to P77,
P80 to P84,P86,P87,P90 to P97
10.0
mA
I OL (avg)
LOW average
output current
P00 to P07,P10 to P17, P20 to P27,P30 to P37,
P40 to P47, P50 to P57, P60 to P67,P70 to P77,
P80 to P84,P86,P87,P90 to P97
5.0
mA
f (XIN)
Main clock input oscillation frequency
(Note 4)
VCC2=2.9 to 5.5V
0
16
MHz
f (XCIN)
f (BCLK)
Sub-clock oscillation frequency
CPU operation clock
VCC2=2.0 to 5.5V(Note 5)
32.768
50
kHz
0
16
MHz
Note 1: Referenced to VCC = VCC1 = VCC2 = 2.0 to 5.5V at Topr = -20 to 70 ˚C unless otherwise specified.
Note 2: The mean output current is the mean value within 100ms.
Note 3: The total IOL (peak) for ports P0, P1, P2, P3, P4, P5,P86, P87, P9 must be 80mA max. The total IOL (peak)
for ports P6, P7andP80 to P84 must be 80mA max. The total IOH (peak) for ports P0, P1, and P2 must be -40mA max.
The total IOH (peak) for ports P3, P4andP5 must be -40mA max.
Note 4: Use the VCC1 and VCC2 power supply voltage on the following conditions.
• VCC1 = 3.00V to VCC2, VCC2 = 4.00V to 5.5V (at f(XIN) = 16MHz)
• VCC1 = 2.90V to VCC2, VCC2 = 2.90V to 5.5V (at f(XIN) = 16MHz, at divide-by-8 or 16)
Note 5: Use in low power dissipation mode. When operating on low voltage (VCC = 3.0V), only single-chip mode can be used.
If the VCC2 supply voltage is less than 2.6 V, be aware that only the CPU, RAM, clock timer, interrupt, and Input/Output ports can be used.
Other control circuits (e.g., timers A and B, serial I/O, UART) cannot be used.
Rev.2.10 Oct 25, 2006 Page 264 of 326
REJ03B0152-0210