PIC18F97J60_11 Datasheet, PDF (347/492 Pages) Microchip Technology – 64/80/100-Pin, High-Performance, 1-Mbit Flash Microcontrollers with Ethernet

PIC18F97J60 FAMILY
22.7 A/D Converter Calibration
The A/D Converter in the PIC18F97J60 family of
devices includes a self-calibration feature which com-
pensates for any offset generated within the module.
The calibration process is automated and is initiated by
setting the ADCAL bit (ADCON0<7>). The next time
the GO/DONE bit is set, the module will perform a
“dummy” conversion (that is, with reading none of the
input channels) and store the resulting value internally
to compensate for offset. Thus, subsequent offsets will
be compensated.
The calibration process assumes that the device is in a
relatively steady-state operating condition. If A/D
calibration is used, it should be performed after each
device Reset, or if there are other major changes in
operating conditions.
22.8 Operation in Power-Managed
Modes
The selection of the automatic acquisition time and A/D
conversion clock is determined in part by the clock
source and frequency while in a power-managed
mode.
If the A/D is expected to operate while the device is in
a power-managed mode, the ACQT<2:0> and
ADCS<2:0> bits in ADCON2 should be updated in
accordance with the power-managed mode clock that
will be used. After the power-managed mode is entered
(either of the power-managed Run modes), an A/D
acquisition or conversion may be started. Once an
acquisition or conversion is started, the device should
continue to be clocked by the same power-managed
mode clock source until the conversion has been
completed. If desired, the device may be placed into
the corresponding power-managed Idle mode during
the conversion.
If the power-managed mode clock frequency is less
than 1 MHz, the A/D RC clock source should be
selected.
Operation in Sleep mode requires the A/D RC clock to
be selected. If bits, ACQT<2:0>, are set to ‘000’ and a
conversion is started, the conversion will be delayed
one instruction cycle to allow execution of the SLEEP
instruction and entry to Sleep mode. The IDLEN and
SCS bits in the OSCCON register must have already
been cleared prior to starting the conversion.
TABLE 22-2: SUMMARY OF A/D REGISTERS
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on Page:
INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE
RBIE TMR0IF INT0IF
RBIF
69
PIR1
PSPIF
ADIF
RC1IF TX1IF SSP1IF CCP1IF TMR2IF TMR1IF
71
PIE1
PSPIE
ADIE
RC1IE TX1IE SSP1IE CCP1IE TMR2IE TMR1IE
71
IPR1
PSPIP
ADIP
RC1IP TX1IP SSP1IP CCP1IP TMR2IP TMR1IP
71
PIR2
OSCFIF CMIF
ETHIF
r
BCL1IF
—
TMR3IF CCP2IF
71
PIE2
OSCFIE CMIE
ETHIE
r
BCL1IE
—
TMR3IE CCP2IE
71
IPR2
OSCFIP CMIP
ETHIP
r
BCL1IP
—
TMR3IP CCP2IP
71
ADRESH A/D Result Register High Byte
70
ADRESL A/D Result Register Low Byte
70
ADCON0 ADCAL
—
CHS3 CHS3 CHS1 CHS0 GO/DONE ADON
70
ADCON1
—
—
VCFG1 VCFG0 PCFG3 PCFG2 PCFG1 PCFG0
70
ADCON2
ADFM
—
ACQT2 ACQT1 ACQT0 ADCS2 ADCS1 ADCS0
70
CCP2CON P2M1
P2M0 DC2B1 DC2B0 CCP2M3 CCP2M2 CCP2M1 CCP2M0 70
PORTA
RJPU
—
RA5
RA4
RA3
RA2
RA1
RA0
72
TRISA
—
—
TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0
71
PORTF
RF7
RF6
RF5
RF4
RF3
RF2
RF1
RF0⁽¹⁾
72
TRISF
TRISF7 TRISF6 TRISF5 TRISF4 TRISF3 TRISF2 TRISF1 TRISF0⁽¹⁾ 71
PORTH⁽²⁾
RH7
RH6
RH5
RH4
RH3
RH2
RH1
RH0
72
TRISH⁽²⁾
TRISH7 TRISH6 TRISH5 TRISH4 TRISH3 TRISH2 TRISH1 TRISH0
71
Legend: — = unimplemented, read as ‘0’, r = reserved. Shaded cells are not used for A/D conversion.
Note 1: Implemented in 100-pin devices only.
2: This register is not implemented in 64-pin devices.
 2011 Microchip Technology Inc.
DS39762F-page 347