|
PIC18F97J60_11 Datasheet, PDF (3/492 Pages) Microchip Technology – 64/80/100-Pin, High-Performance, 1-Mbit Flash Microcontrollers with Ethernet | |||
|
◁ |
PIC18F97J60 FAMILY
64/80/100-Pin High-Performance,
1-Mbit Flash Microcontrollers with Ethernet
Ethernet Features:
⢠IEEE 802.3⢠Compatible Ethernet Controller
⢠Fully Compatible with 10/100/1000Base-T Networks
⢠Integrated MAC and 10Base-T PHY
⢠8-Kbyte Transmit/Receive Packet Buffer SRAM
⢠Supports One 10Base-T Port
⢠Programmable Automatic Retransmit on Collision
⢠Programmable Padding and CRC Generation
⢠Programmable Automatic Rejection of Erroneous
Packets
⢠Activity Outputs for 2 LED Indicators
⢠Buffer:
- Configurable transmit/receive buffer size
- Hardware-managed circular receive FIFO
- Byte-wide random and sequential access
- Internal DMA for fast memory copying
- Hardware assisted checksum calculation for
various protocols
⢠MAC:
- Support for Unicast, Multicast and Broadcast
packets
- Programmable Pattern Match of up to 64 bytes
within packet at user-defined offset
- Programmable wake-up on multiple packet
formats
⢠PHY:
- Wave shaping output filter
Flexible Oscillator Structure:
⢠Selectable System Clock derived from Single
25 MHz External Source:
- 2.778 to 41.667 MHz
⢠Internal 31 kHz Oscillator
⢠Secondary Oscillator using Timer1 @ 32 kHz
⢠Fail-Safe Clock Monitor:
- Allows for safe shutdown if oscillator stops
⢠Two-Speed Oscillator Start-up
External Memory Bus
(100-pin devices only):
⢠Address Capability of up to 2 Mbytes
⢠8-Bit or 16-Bit Interface
⢠12-Bit, 16-Bit and 20-Bit Addressing modes
Peripheral Highlights:
⢠High-Current Sink/Source: 25 mA/25 mA on PORTB
and PORTC
⢠Five Timer modules (Timer0 to Timer4)
⢠Four External Interrupt pins
⢠Two Capture/Compare/PWM (CCP) modules
⢠Three Enhanced Capture/Compare/PWM (ECCP)
modules:
- One, two or four PWM outputs
- Selectable polarity
- Programmable dead time
- Auto-shutdown and auto-restart
⢠Up to Two Master Synchronous Serial Port (MSSP)
modules supporting SPI (all 4 modes) and I2Câ¢
Master and Slave modes
⢠Up to Two Enhanced USART modules:
- Supports RS-485, RS-232 and LIN/J2602
- Auto-wake-up on Start bit
- Auto-Baud Detect (ABD)
⢠10-Bit, Up to 16-Channel Analog-to-Digital Converter
module (A/D):
- Auto-acquisition capability
- Conversion available during Sleep
⢠Dual Analog Comparators with Input Multiplexing
⢠Parallel Slave Port (PSP) module
(100-pin devices only)
Special Microcontroller Features:
⢠5.5V Tolerant Inputs (digital-only pins)
⢠Low-Power, High-Speed CMOS Flash Technology:
- Self-reprogrammable under software control
⢠C compiler Optimized Architecture for Reentrant Code
⢠Power Management Features:
- Run: CPU on, peripherals on
- Idle: CPU off, peripherals on
- Sleep: CPU off, peripherals off
⢠Priority Levels for Interrupts
⢠8 x 8 Single-Cycle Hardware Multiplier
⢠Extended Watchdog Timer (WDT):
- Programmable period from 4 ms to 134s
⢠Single-Supply 3.3V In-Circuit Serial Programmingâ¢
(ICSPâ¢) via Two Pins
⢠In-Circuit Debug (ICD) with 3 Breakpoints via
Two Pins
⢠Operating Voltage Range of 2.35V to 3.6V (3.1V to
3.6V using Ethernet module)
⢠On-Chip 2.5V Regulator
ï£ 2011 Microchip Technology Inc.
DS39762F-page 3
|
▷ |