PIC18F87K22 Datasheet, PDF (487/548 Pages) Microchip Technology – 64/80-Pin, High-Performance, 1-Mbit Enhanced Flash Microcontrollers with 12-Bit A/D and nanoWatt XLP Technology

PIC18F87K22 FAMILY
31.2 DC Characteristics: Power-Down and Supply Current
PIC18F87K22 Family (Industrial) (Continued)
PIC18F87K22 Family
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C  TA  +85°C for industrial
Param
No.
Device
Typ
Max Units
Conditions
Supply Current (IDD)^(2,3)
All devices 5.3
5.5
5.5
All devices 10
10
11
All devices 70
80
90
All devices 410
410
410
All devices 680
683
670
All devices 760
780
800
All devices 760
760
770
All devices 1.4
1.4
1.4
10 A
10 A
10 A
15 A
16 A
17 A
180 A
185 A
190 A
850 A
800 A
830 A
990 A
960 A
950 A
1400 A
1400 A
1500 A
1300 A
1400 A
1500 A
2.5 mA
2.5 mA
2.5 mA
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
VDD = 1.8V⁽⁴⁾
Regulator Disabled
VDD = 3.3V⁽⁴⁾
Regulator Disabled
VDD = 5V⁽⁵⁾
Regulator Enabled
VDD = 1.8V⁽⁴⁾
Regulator Disabled
VDD = 3.3V⁽⁴⁾
Regulator Disabled
VDD = 5V⁽⁵⁾
Regulator Enabled
VDD = 1.8V⁽⁴⁾
Regulator Disabled
VDD = 3.3V⁽⁴⁾
Regulator Disabled
FOSC = 31 kHz
(RC_RUN mode,
LF-INTOSC)
FOSC = 1 MHz
(RC_RUN mode,
HF-INTOSC)
FOSC = 4 MHz
(RC_RUN mode,
HF-INTOSC)
All devices 1.5
1.5
1.5
2.7 mA
2.7 mA
2.7 mA
-40°C
+25°C
+85°C
VDD = 5V⁽⁵⁾
Regulator Enabled
Note 1:
2:
3:
4:
5:
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in a high-impedance state and tied to VDD or VSS, and all features that add delta
current are disabled (such as WDT, SOSC oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
Standard, low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
Voltage regulator disabled (ENVREG = 0, tied to VSS, RETEN (CONFIG1L<0>) = 1).
Voltage regulator enabled (ENVREG = 1, tied to VDD, SRETEN (WDTCON<4>) = 1 and RETEN (CONFIG1L<0>) = 0).
 2010 Microchip Technology Inc.
Preliminary
DS39960B-page 487