PIC18F6X2X Datasheet, PDF (356/386 Pages) Microchip Technology – 64/80-Pin High Performance, 64-Kbyte Enhanced FLASH Microcontrollers with A/D

PIC18F6X2X/8X2X
TABLE 27-22: MASTER SSP I²C BUS DATA REQUIREMENTS
Param.
No.
Symbol
Characteristic
Min
Max Units
Conditions
100 THIGH Clock high time 100 kHz mode 2(TOSC)(BRG + 1) — ms
400 kHz mode 2(TOSC)(BRG + 1) — ms
1 MHz mode⁽¹⁾ 2(TOSC)(BRG + 1) —
ms
101 TLOW Clock low time 100 kHz mode 2(TOSC)(BRG + 1) — ms
400 kHz mode 2(TOSC)(BRG + 1) — ms
1 MHz mode⁽¹⁾ 2(TOSC)(BRG + 1) —
ms
102 TR
SDA and SCL
rise time
100 kHz mode
400 kHz mode
1 MHz mode⁽¹⁾
—
20 + 0.1 CB
—
1000
300
300
ns CB is specified to be from
ns ^{10 to 400 pF}
ns
103 TF
SDA and SCL
fall time
100 kHz mode
400 kHz mode
1 MHz mode⁽¹⁾
—
20 + 0.1 CB
—
300 ns CB is specified to be from
300 ns ^{10 to 400 pF}
100 ns
90
TSU:STA START condition 100 kHz mode 2(TOSC)(BRG + 1) — ms Only relevant for
setup time
400 kHz mode 2(TOSC)(BRG + 1) —
1 MHz mode⁽¹⁾ 2(TOSC)(BRG + 1) —
ms ^{Repeated START}
condition
ms
91
THD:STA START condition 100 kHz mode 2(TOSC)(BRG + 1) — ms After this period, the first
hold time
400 kHz mode 2(TOSC)(BRG + 1) —
ms ^{clock pulse is generated}
1 MHz mode⁽¹⁾ 2(TOSC)(BRG + 1) —
ms
106 THD:DAT Data input
hold time
100 kHz mode
400 kHz mode
1 MHz mode⁽¹⁾
0
0
TBD
—
ns
0.9 ms
—
ns
107 TSU:DAT Data input
setup time
100 kHz mode
400 kHz mode
1 MHz mode⁽¹⁾
250
100
TBD
—
ns (Note 2)
—
ns
—
ns
92
TSU:STO STOP condition 100 kHz mode 2(TOSC)(BRG + 1) — ms
setup time
400 kHz mode 2(TOSC)(BRG + 1) — ms
1 MHz mode⁽¹⁾ 2(TOSC)(BRG + 1) —
ms
109 TAA
Output valid from 100 kHz mode
clock
400 kHz mode
1 MHz mode⁽¹⁾
—
3500 ns
—
1000 ns
—
—
ns
110 TBUF Bus free time 100 kHz mode
400 kHz mode
1 MHz mode⁽¹⁾
4.7
1.3
TBD
— ms Time the bus must be free
—
ms ^{before a new transmission}
can start
— ms
D102 CB
Bus capacitive loading
—
400 pF
Note 1: Maximum pin capacitance = 10 pF for all I²C pins.
2: A fast mode I²C bus device can be used in a standard mode I²C bus system but parameter #107 ≥ 250 ns
must then be met. This will automatically be the case if the device does not stretch the low period of the SCL
signal. If such a device does stretch the low period of the SCL signal, it must output the next data bit to the
SDA line, parameter #102.+ parameter #107 = 1000 + 250 = 1250 ns (for 100 kHz mode), before the SCL
line is released.
DS39612A-page 354
Advance Information
 2003 Microchip Technology Inc.