XRT72L13 Datasheet, PDF (34/370 Pages) Exar Corporation – M13 MULTIPLEXER/CLEAR CHANNEL DS3 FRAMER IC

XRT72L13
M13 MULTIPLEXER/CLEAR CHANNEL DS3 FRAMER IC
REV. P1.0.6
áç
PRELIMINARY
PIN DESCRIPTIONS
PIN #
124
NAME
TxDS1Clk_13
125
TxDS1Data_12
126
TxDS1Clk_12
127
TxDS1Data_11
128
GND
129
TxDS1Clk_11
130
TxDS1Data_10
131
TxDS1Clk_10
132
TxDS1Data_9
133
TxDS1Clk_9
TYPE
I
I
I
I
****
I
I
I
I
I
DESCRIPTION
Transmit DS1/E1 Clock Input - Channel 13:
This input pin accepts either a DS1 (1.544MHz) or an E1 (2.048MHz)
clock signal from the Terminal Equipment. The falling edge of this sig-
nal is used to sample the data at the "TxDS1Data_13" input pin.
Transmit DS1/E1 Data Input - Channel 12:
This input pin accepts either a DS1 or E1 signal from the Terminal
Equipment. This input pin is sampled upon the "falling edge" of the
TxDS1Clk_12 signal.
Transmit DS1/E1 Clock Input - Channel 12:
This input pin accepts either a DS1 (1.544MHz) or an E1 (2.048MHz)
clock signal from the Terminal Equipment. The falling edge of this sig-
nal is used to sample the data at the "TxDS1Data_12" input pin.
Transmit DS1 Data Input - Channel 11:
This input pin accepts a DS1 signal from the Terminal Equipment.
This input pin is sampled upon the "falling edge" of the TxDS1Clk_11
signal.
NOTES:
1. This input pin is inactive if the corresponding M12 MUX is
multiplexing 3 E1's into an ITU-T G.747 data stream.
2. This input pin accepts DS2 data if M12 MUX # 3 is bypassed.
Ground Pin
Transmit DS1 Clock Input - Channel 11:
This input pin accepts a DS1 (1.544MHz) clock signal from the Termi-
nal Equipment. The falling edge of this signal is used to sample the
data at the "TxDS1Data_11" input pin.
NOTES:
1. This input pin is inactive if the corresponding M12 MUX is
multiplexing 3 E1's into an ITU-T G.747 data stream.
2. This input pin accepts a DS2 rate clock signal (6.312MHz)
if M12 MUX # 3 is bypassed.
Transmit DS1/E1 Data Input - Channel 10:
This input pin accepts either a DS1 or E1 signal from the Terminal
Equipment. This input pin is sampled upon the "falling edge" of the
TxDS1Clk_10 signal.
Transmit DS1/E1 Clock Input - Channel 10:
This input pin accepts either a DS1 (1.544MHz) or an E1 (2.048MHz)
clock signal from the Terminal Equipment. The falling edge of this sig-
nal is used to sample the data at the "TxDS1Data_10" input pin.
Transmit DS1/E1 Data Input - Channel 9:
This input pin accepts either a DS1 or E1 signal from the Terminal
Equipment. This input pin is sampled upon the "falling edge" of the
TxDS1Clk_9 signal.
Transmit DS1/E1 Clock Input - Channel 9:
This input pin accepts either a DS1 (1.544MHz) or an E1 (2.048MHz)
clock signal from the Terminal Equipment. The falling edge of this sig-
nal is used to sample the data at the "TxDS1Data_9" input pin.
22