XRT72L13 Datasheet, PDF (127/370 Pages) Exar Corporation – M13 MULTIPLEXER/CLEAR CHANNEL DS3 FRAMER IC

áç
PRELIMINARY
M13 MULTIPLEXER/CLEAR CHANNEL DS3 FRAMER IC XRT72L13
REV. 1.0.6
When this loop-back is configured, then the
“RxDS1Data_11” signal will internally be “looped-
back” into the “TxDS1Data_11” path. Further, the
“RxDS1Clock_11” clock signal will also be internally
looped back into the “RxDS1Clock_11” signal path.
Setting this bit-field to “1” enables this loop-back
mode. Conversely, setting this bit-field to “0” disables
this loop-back mode.
NOTE: This bit-field is ignored if the XRT72L13 has been
configured to operate in the “ITU-T G.747” Mode.
Bit 6 - Loop-back Activation - DS1 Channel 10
This “Read/Write” bit-field permits the user to config-
ure DS1 Channel 10 into Remote Loop-back Mode.
When this loop-back is configured, then the
“RxDS1Data_10” signal will internally be “looped-
back” into the “TxDS1Data_10” path. Further, the
“RxDS1Clock_10” clock signal will also be internally
looped back into the “RxDS1Clock_10” signal path.
Setting this bit-field to “1” enables this loop-back
mode. Conversely, setting this bit-field to “0” disables
this loop-back mode.
Bit 5 - Loop-back Activation - DS1 Channel 9
This “Read/Write” bit-field permits the user to config-
ure DS1 Channel 9 into Remote Loop-back Mode.
When this loop-back is configured, then the
“RxDS1Data_9” signal will internally be “looped-back”
into the “TxDS1Data_9” path. Further, the
“RxDS1Clock_9” clock signal will also be internally
looped back into the “RxDS1Clock_9” signal path.
Setting this bit-field to “1” enables this loop-back
mode. Conversely, setting this bit-field to “0” disables
this loop-back mode.
Bit 4 - Loop-back Activation - DS1 Channel 8
This “Read/Write” bit-field permits the user to config-
ure DS1 Channel 8 into Remote Loop-back Mode.
When this loop-back is configured, then the
“RxDS1Data_8” signal will internally be “looped-back”
into the “TxDS1Data_8” path. Further, the
“RxDS1Clock_8” clock signal will also be internally
looped back into the “RxDS1Clock_8” signal path.
Setting this bit-field to “1” enables this loop-back
mode. Conversely, setting this bit-field to “0” disables
this loop-back mode.
Bit 3 - Loop-back Request - DS1 Channel 11
This “Read/Write” bit-field permits the user to config-
ure the XRT72L13 to transmit a “DS1 Channel 11 -
Loop-back Request” signal to the Remote Terminal
Equipment. When the Remote Terminal Equipment
receives this request, it is expected to respond by
configuring its own DS1 Channel 11 signal into Loop-
back Mode.
NOTE: This bit-field is ignored if the XRT72L13 has been
configured to operate in the “ITU-T G.747” Mode.
Bit 2 - Loop-back Request - DS1 Channel 10
This “Read/Write” bit-field permits the user to config-
ure the XRT72L13 to transmit a “DS1 Channel 10 -
Loop-back Request” signal to the Remote Terminal
Equipment. When the Remote Terminal Equipment
receives this request, it is expected to respond by
configuring its own DS1 Channel 10 signal into Loop-
back Mode.
NOTE: This bit-field is ignored if the XRT72L13 has been
configured to operate in the “ITU-T G.747” Mode.
Bit 1 - Loop-back Request - DS1 Channel 9
This “Read/Write” bit-field permits the user to config-
ure the XRT72L13 to transmit a “DS1 Channel 9 -
Loop-back Request” signal to the Remote Terminal
Equipment. When the Remote Terminal Equipment
receives this request, it is expected to respond by
configuring its own DS1 Channel 9 signal into Loop-
back Mode.
NOTE: This bit-field is ignored if the XRT72L13 has been
configured to operate in the “ITU-T G.747” Mode.
Bit 0 - Loop-back Request - DS1 Channel 8
This “Read/Write” bit-field permits the user to config-
ure the XRT72L13 to transmit a “DS1 Channel 8 -
Loop-back Request” signal to the Remote Terminal
Equipment. When the Remote Terminal Equipment
receives this request, it is expected to respond by
configuring its own DS1 Channel 8 signal into Loop-
back Mode.
NOTE: This bit-field is ignored if the XRT72L13 has been
configured to operate in the “ITU-T G.747” Mode.
2.3.2.41 M12 DS2 # 4 Loop-back Request Regis-
ter
115