|
XRT72L13 Datasheet, PDF (164/370 Pages) Exar Corporation – M13 MULTIPLEXER/CLEAR CHANNEL DS3 FRAMER IC | |||
|
◁ |
XRT72L13 MULTIPLEXER/FRAMER IC
REV. 1.0.6
áç
PRELIMINARY
2.3.2.105 M12 DS2 # 4 Loopback Interrupt/Inter-
rupt Enable Register
M12 DS2 # 4 LOOP-BACK INTERRUPT/INTERRUPT ENABLE REGISTER (ADDRESS = 0X99)
BIT 7
DS1
Channel 15
Loop-back
Interrupt
RUR
0
BIT 6
DS1
Channel 14
Loop-back
Interrupt
RUR
0
BIT 5
DS1
Channel 13
Loop-back
Interrupt
RUR
0
BIT 4
DS1
Channel 12
Loop-back
Interrupt
RUR
0
BIT 3
DS1
Channel 15
Loop-backj
Interrupt
Enable
R/W
0
BIT 2
DS1
Channel 14
Loop-backj
Interrupt
Enable
R/W
0
BIT 1
DS1
Channel 13
Loop-backj
Interrupt
Enable
R/W/
0
BIT 0
DS1
Channel 12
Loop-backj
Interrupt
Enable
R/W
0
Bit 7 - DS1 Channel 15 Loop-back Request Inter-
rupt Status
This âReset-upon-Readâ bit-field indicates whether
the âDS1 Channel 15 Loop-back Requestâ interrupt
has occurred or not.
This bit-field will be set to â1â if the âDS1 Channel 15
Loop-back Request Interruptâ has occurred since the
last read of this register.
This bit-field will be set to â0â if the âDS1 Channel 15
Loop-back Requestâ interrupt has NOT occurred
since the last read of this register.
NOTE: This bit-field is ignored if the XRT72L13 is config-
ured to operate in the âITU-T G.747 Modeâ.
Bit 6 - DS1 Channel 14 Loop-back Request Inter-
rupt Status
This âReset-upon-Readâ bit-field indicates whether
the âDS1 Channel 14 Loop-back Requestâ interrupt
has occurred or not.
This bit-field will be set to â1â if the âDS1 Channel 14
Loop-back Request Interruptâ has occurred since the
last read of this register.
This bit-field will be set to â0â if the âDS1 Channel 14
Loop-back Requestâ interrupt has NOT occurred
since the last read of this register.
Bit 5 - DS1 Channel 13 Loop-back Request Inter-
rupt Status
This âReset-upon-Readâ bit-field indicates whether
the âDS1 Channel 13 Loop-back Requestâ interrupt
has occurred or not.
This bit-field will be set to â1â if the âDS1 Channel 13
Loop-back Request Interruptâ has occurred since the
last read of this register.
This bit-field will be set to â0â if the âDS1 Channel 13
Loop-back Requestâ interrupt has NOT occurred
since the last read of this register.
Bit 4 - DS1 Channel 12 Loop-back Request Inter-
rupt Status
This âReset-upon-Readâ bit-field indicates whether
the âDS1 Channel 12 Loop-back Requestâ interrupt
has occurred or not.
This bit-field will be set to â1â if the âDS1 Channel 12
Loop-back Request Interruptâ has occurred since the
last read of this register.
This bit-field will be set to â0â if the âDS1 Channel 12
Loop-back Requestâ interrupt has NOT occurred
since the last read of this register.
Bit 3 - DS1 Channel 15 Loop-back Request Inter-
rupt Enable
This âRead/Writeâ bit-field permits the user to enable
or disable the âDS1 Channel 15 Loop-back Requestâ
Interrupt.
Setting this bit to â0â disables this interrupt. Con-
versely, setting this bit to â1â enables this interrupt.
Bit 2 - DS1 Channel 14 Loop-back Request Inter-
rupt Enable
This âRead/Writeâ bit-field permits the user to enable
or disable the âDS1 Channel 14 Loop-back Requestâ
Interrupt.
Setting this bit to â0â disables this interrupt. Con-
versely, setting this bit to â1â enables this interrupt.
Bit 1 - DS1 Channel 13 Loop-back Request Inter-
rupt Enable
This âRead/Writeâ bit-field permits the user to enable
or disable the âDS1 Channel 13 Loop-back Requestâ
Interrupt.
Setting this bit to â0â disables this interrupt. Con-
versely, setting this bit to â1â enables this interrupt.
Bit 0 - DS1 Channel 12 Loop-back Request Inter-
rupt Enable
This âRead/Writeâ bit-field permits the user to enable
or disable the âDS1 Channel 12 Loop-back Requestâ
Interrupt.
152
|
▷ |