XRT72L13 Datasheet, PDF (287/370 Pages) Exar Corporation – M13 MULTIPLEXER/CLEAR CHANNEL DS3 FRAMER IC

áç
PRELIMINARY
XRT72L13
M13 MULTIPLEXER/CLEAR CHANNEL DS3 FRAMER IC
REV. P1.0.6
By default, the Transmit DS3 Framer block will set the
three (3) FEBE bit-fields to [1, 1, 1] if all of the follow-
ing conditions are true.
• The “Local” Receive DS3 Framer block detects a
“CP” bit Error in the most recently received DS3
frame.
• The “Local” Receive DS3 Framer block detects no
P-Bit Errors.
• The “Local” Receive DS3 Framer block detects no
CP-Bit Errors
Conversely, the Transmit DS3 Framer block will set
the three (3) FEBE bit-fields to a value other than [1,
1, 1] if any one of the following conditions are true.
• The “Local” Receive DS3 Framer block detects a P-
bit Error in the most recently received DS3 frame.
4.2.4.2.2 Generating Errored DS3 Frames
The Transmit DS3 Framer block permits the user to
insert errors into the framing and error detection over-
head bits (e.g., the P, M and F-bits) of the "outbound"
DS3 data stream in order to support "Far-End" Equip-
ment testing. The user can exercise this option by
writing data to any of the numerous Transmit DS3
Mask Registers. These "Mask Registers" and their
comprising bit-fields are defined below.
TX DS3 M-BIT MASK REGISTER, ADDRESS = 0X35
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT2
BIT 1
BIT 0
TxFEBE
DAT[2]
TxFEBE
DAT[1]
TxFEBE
DAT[0]
FEBE Reg
Enable
TxErr PBit MBit Mask(2) MBit Mask(1) MBit Mask(0)
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
X
X
X
X
X
X
X
X
The bit-fields of the Tx DS3 M-bit Mask Register, that
are relevant to error-insertion are shaded. The re-
maining bit-fields pertain to the FEBE bit-fields, and
are discussed in Section 4.2.4.2.1.9.
The Tx DS3 M-Bit Mask Register serves two purpos-
es
1. It allows the user to transmit his/her own value for
FEBE (3 bits) - please see Section 4.2.4.2.1.9.
2. It allows the user to transmit errored P-bits.
3. It allows the user to insert errors into the M-bit
(framing bits) in order to support equipment test-
ing.
Each of these bit-fields are discussed below.
Bit 3 - Tx Err (Transmit Errored) P-Bit
This bit-field allows the user to insert errors into the
P-bits, of each outbound DS3 Frame, for equipment
testing purposes. If this bit-field is "0", then the P-Bits
are transmitted as calculated from the payload of the
previous DS3 frames. However, if this bit-field is "1",
then the P-bits are inverted (from their calculated val-
ue) prior to transmission.
The Transmit DS3 Framer will automatically perform
an XOR operation with the M-bits (in the DS3 data-
stream) and the contents of the corresponding bit-
field, within this register. The results of this operation
will be written back into the M-bit positions within the
"outbound" DS3 Frames. Therefore, if the user does
not wish to insert errors into the M-bits, he/she must
make sure that the contents of these bit-fields: M-Bit
Mask[2:0] are "0".
F-Bit Error Insertion
The remaining mask registers (Tx DS3 F-Bit Mask1
through Mask4 registers) contain bit-fields which cor-
respond to each of the 28 F-bits, within the DS3
frame. Prior to transmission, these bit-fields are auto-
matically XORed with the contents of the correspond-
ing bit fields within these Mask Registers. The result
of this XOR operation is written back into the corre-
sponding bit-field, within the outgoing DS3 frame, and
is transmitted on the line. Therefore, if the user does
not wish to modify any of these bits, then he/she must
insure that these registers contain all "0s" (the default
value).
Bits 2 - 0: M-Bit Mask[2:0]
TX DS3 F-BIT MASK1 REGISTER, ADDRESS = 0X36
BIT 7
Unused
RO
0
BIT 6
Unused
RO
0
BIT 5
Unused
RO
0
BIT 4
Unused
RO
0
BIT 3
BIT2
BIT 1
BIT 0
FBit Mask(27) FBit Mask(26) FBit Mask(25) FBit Mask(24)
R/W
R/W
R/W
R/W
0
0
0
0
275