XRT72L13 Datasheet, PDF (133/370 Pages) Exar Corporation – M13 MULTIPLEXER/CLEAR CHANNEL DS3 FRAMER IC

áç
PRELIMINARY
M13 MULTIPLEXER/CLEAR CHANNEL DS3 FRAMER IC XRT72L13
REV. 1.0.6
Writing a "1" to this bit-field invokes this command.
Writing a "0" allows the Transmit DS3 Framer to func-
tion normally (e.g., the Transmit DS3 Framer will
transmit its payload and internally generated over-
head bits).
NOTE: For more information on this feature, please see
Section _.
NOTE: This bit-setting is ignored if Bits 3 or 4 (within this
register) are set to "1".
Bit 4 - Tx AIS (Pattern)
This "Read/Write" bit-field allows the user to com-
mand the Transmit DS3 Framer to transmit an "AIS"
pattern. If the user invokes this command, then the
Transmit DS3 Framer will force the outbound DS3
frames to have the following patterns.
• Valid M-bits, F-bits, and P-bits
• All C-bits are set to '0'
• All X-bits are set to '1'
• A repeating '1010...' pattern is written into the pay-
load of the DS3 Frames.
Writing a "1' to this bit-field invokes this command.
Writing a "0" allows the Transmit DS3 Framer to func-
tion normally (e.g., the Transmit DS3 Framer will
transmit its payload and internally generated over-
head bits).
NOTE: For more information on this feature, please see
Section _.
Bit 3 - Tx LOS (Loss of Signal)
This "Read/Write" bit-field allows the user to com-
mand the Transmit DS3 Framer to simulate an "LOS
Condition". If the user invokes this command, then
the Transmit DS3 Framer will stop sending "mark"
pulses out on the line; and will transmit an all-zero
pattern.
Writing a '0' to this bit-field disables (or shuts off) this
feature, thereby allowing internally generated DS3
Frames to be generated and transmitted over the line.
Writing a '1' to this bit-field invokes this command,
causing the Transmit DS3 Framing to generate an all
'0' pattern.
NOTE: For more information on this feature, please see
Section _.
Bit 2 - FERF on LOS
This "Read/Write" bit-field allows the user to config-
ure the Transmit DS3 Framer to generate a "Yellow
Alarm" if the Near-End Receive DS3 Framer detects
a "LOS" (Loss of Signal) Condition.
Writing a "1" to this bit-field enables this feature. Writ-
ing a "0" to this bit-field disables this feature.
NOTE: For more information on this feature, please see
Section _.
Bit 1 - FERF on OOF
This "Read/Write" bit-field allows the user to config-
ure the Transmit DS3 Framer to generate a "Yellow
Alarm" if the Near-End Receive DS3 Framer detects
an "OOF (Out-of-Frame) Condition".
Writing a "1" to this bit-field enables this feature. Writ-
ing a "0" to this bit-field disables this feature.
NOTE: For more information on this feature, please see
Section _.
Bit 0 - FERF on AIS
This "Read/Write" bit-field allows the user to config-
ure the Transmit DS3 Framer to generate a "Yellow
Alarm" if the Near-End Receive DS3 Framer detects
an AIS (Alarm Indication Signal) Condition.
Writing a "1" to this bit-field enables this feature. Writ-
ing a "0" to this bit-field disables this feature.
NOTE: For more information on this feature, please see
Section _.
2.3.2.46 TxDS3 FEAC Configuration and Status
Register )
TRANSMIT DS3 CONFIGURATION & STATUS REGISTER (ADDRESS = 0X31)
BIT 7
RO
0
BIT 6
Not Used
RO
0
BIT 5
RO
0
BIT 4
Tx FEAC
Interrupt
Enable
R/W
0
BIT 3
TxFEAC
Interrupt
Status
RUR
0
BIT 2
TxFEAC
Enable
R/W
0
BIT 1
TxFEAC
Go
R/W
0
BIT 0
TxFEAC
Busy
RO
0
Bit 4 - Tx FEAC Interrupt Enable
This “Read-Write” bit-field permits the user to enable
or disable the “Transmit FEAC” Interrupt.
Setting this bit-field to “0” disables this interrupt.
Conversely, setting this bit-field to “1” enables this in-
terrupt.
Bit 3 - TxFEAC Interrupt Status
121