English
Language : 

XRT72L13 Datasheet, PDF (163/370 Pages) Exar Corporation – M13 MULTIPLEXER/CLEAR CHANNEL DS3 FRAMER IC
áç
PRELIMINARY
M13 MULTIPLEXER/CLEAR CHANNEL DS3 FRAMER IC XRT72L13
REV. 1.0.6
This “Read/Write” bit-field permits the user to enable
or disable the “DS1 Channel 11 Loop-back Request”
Interrupt.
Setting this bit to “0” disables this interrupt. Con-
versely, setting this bit to “1” enables this interrupt.
Bit 2 - DS1 Channel 10 Loop-back Request Inter-
rupt Enable
This “Read/Write” bit-field permits the user to enable
or disable the “DS1 Channel 10 Loop-back Request”
Interrupt.
Setting this bit to “0” disables this interrupt. Con-
versely, setting this bit to “1” enables this interrupt.
Bit 1 - DS1 Channel 9 Loop-back Request Inter-
rupt Enable
This “Read/Write” bit-field permits the user to enable
or disable the “DS1 Channel 9 Loop-back Request”
Interrupt.
Setting this bit to “0” disables this interrupt. Con-
versely, setting this bit to “1” enables this interrupt.
Bit 0 - DS1 Channel 8 Loop-back Request Inter-
rupt Enable
This “Read/Write” bit-field permits the user to enable
or disable the “DS1 Channel 8 Loop-back Request”
Interrupt.
Setting this bit to “0” disables this interrupt. Con-
versely, setting this bit to “1” enables this interrupt.
2.3.2.104 M12 DS2 # 3 Loopback Status Register
M12 DS2 # 1 LOOP-BACK STATUS REGISTER (ADDRESS = 0X98)
BIT 7
R/O
0
BIT 6
BIT 5
Unused
R/O
R/O
0
0
BIT 4
/RO
0
BIT 3
BIT 2
BIT 1
DS1
DS1
Channel # 11 Channel # 10
Loopback Loopback
Status
Status
R/O
R/O
0
0
DS1
Channel # 9
Loopback
Status
R/O
0
BIT 0
DS1
Channel # 8
Loopback
Status
R/O
0
Bit 3 - DS1 Channel # 11 Loop-back Status
This “Read-Only” bit-field indicates whether or not a
loop-back request has been detected for DS1 Chan-
nel # 11.
This bit-field will be set to “1” if a loop-back request
has been detected for DS1 Channel # 11. Converse-
ly, this bit-field will be set to “0” if a loop-back request
has NOT been detected for DS1 Channel # 11.
NOTE: This bit-field is invalid if the XRT72L13 M13 device
is operating in the “ITU-T G.747” Mode.
Bit 2 - DS1 Channel # 10 Loop-back Status
This “Read-Only” bit-field indicates whether or not a
loop-back request has been detected for DS1 Chan-
nel # 10.
This bit-field will be set to “1” if a loop-back request
has been detected for DS1 Channel # 10. Converse-
ly, this bit-field will be set to “0” if a loop-back request
has NOT been detected for DS1 Channel # 10.
Bit 1 - DS1 Channel # 9 Loop-back Status
This “Read-Only” bit-field indicates whether or not a
loop-back request has been detected for DS1 Chan-
nel # 9.
This bit-field will be set to “1” if a loop-back request
has been detected for DS1 Channel # 9. Conversely,
this bit-field will be set to “0” if a loop-back request
has NOT been detected for DS1 Channel # 9.
Bit 0 - DS1 Channel # 8 Loop-back Status
This “Read-Only” bit-field indicates whether or not a
loop-back request has been detected for DS1 Chan-
nel # 8.
This bit-field will be set to “1” if a loop-back request
has been detected for DS1 Channel # 8. Conversely,
this bit-field will be set to “0” if a loop-back request
has NOT been detected for DS1 Channel # 8.
151