English
Language : 

PIC18F47J53 Datasheet, PDF (527/586 Pages) Microchip Technology – 28/44-Pin, High-Performance USB Microcontrollers with nanoWatt XLP Technology
PIC18F47J53 FAMILY
31.3 DC Characteristics:PIC18F47J53 Family (Industrial)
DC CHARACTERISTICS
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA  +85°C for industrial
Param
No.
Symbol
Characteristic
Min
Max Units
Conditions
VIL
D030
D030A
D031
D031A
D031B
D032
D033
D033A
Input Low Voltage
All I/O ports:
with TTL Buffer(4)
with TTL Buffer(4)
with Schmitt Trigger Buffer
SCLx/SDAx
SCLx/SDAx
MCLR
OSC1
OSC1
VSS
0.15 VDD V VDD < 3.3V
VSS
0.8
V 3.3V < VDD <3.6V
VSS
0.2 VDD V
—
0.3 VDD V I2C™ enabled
—
0.8
V SMBus enabled
VSS
0.2 VDD V
VSS
0.3 VDD V HS, HSPLL modes
VSS
0.2 VDD V EC, ECPLL modes
D034
VIH
D040
D040A
D041
Dxxx
DxxxA
Dxxx
D041A
D041B
D042
D043
D043A
T1OSI
VSS
0.3
Input High Voltage
I/O Ports without 5.5V
Tolerance:
with TTL Buffer(4)
with TTL Buffer(4)
0.25 VDD + 0.8V VDD
2.0
VDD
with Schmitt Trigger Buffer
0.8 VDD
VDD
I/O Ports with 5.5V Tolerance:(5)
with TTL Buffer
0.25 VDD + 0.8V 5.5
2.0
5.5
with Schmitt Trigger Buffer
0.8 VDD
5.5
SCLx/SDAx
0.7 VDD
—
SCLx/SDAx
2.1
—
MCLR
0.8 VDD
5.5
OSC1
0.7 VDD
VDD
OSC1
0.8 VDD
VDD
V T1OSCEN = 1
V VDD < 3.3V
V 3.3V < VDD <3.6V
V
V VDD < 3.3V
V 3.3V  VDD 3.6V
V
V I2C™ enabled
V SMBus enabled; VDD > 3V
V
V HS, HSPLL modes
V EC, ECPLL modes
D044
IIL
D060
T1OSI
Input Leakage Current(1,2)
I/O Ports
1.6
VDD
V T1OSCEN = 1
±5
±200
nA VSS VPIN VDD,
Pin at high-impedance
D061
D062
D063
D070
IPU
IPURB
MCLR
D+/D-
OSC1
Weak Pull-up Current
PORTB, PORTD(3) and
PORTE(3) Weak Pull-up Current
±5
±75 typical
±5
80
±200
±500
±200
400
nA Vss VPIN VDD
nA Vss VPIN VDD
nA Vss VPIN VDD
A VDD = 3.3V, VPIN = VSS
Note 1:
2:
3:
4:
5:
The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent
normal operating conditions. Higher leakage current may be measured at different input voltages.
Negative current is defined as current sourced by the pin.
Only available in 44-pin devices.
When used as general purpose inputs, the RC4 and RC5 thresholds are referenced to VUSB instead of VDD.
Refer to Table 10-2 for pin tolerance levels.
 2010 Microchip Technology Inc.
Preliminary
DS39964B-page 527