PIC18F6525_13 Datasheet, PDF (259/400 Pages) Microchip Technology – 64/80-Pin High-Performance, 64-Kbyte Enhanced Flash Microcontrollers with A/D

PIC18F6525/6621/8525/8621
24.0 SPECIAL FEATURES OF THE CPU
There are several features intended to maximize
system reliability, minimize cost through elimination of
external components, provide power-saving operating
modes and offer code protection. These are:
• Oscillator Selection
• Reset
- Power-on Reset (POR)
- Power-up Timer (PWRT)
- Oscillator Start-up Timer (OST)
- Brown-out Reset (BOR)
• Interrupts
• Watchdog Timer (WDT)
• Sleep
• Code Protection
• ID Locations
• In-Circuit Serial Programming
All PIC18F6525/6621/8525/8621 devices have a
Watchdog Timer which is permanently enabled via the
configuration bits, or software controlled. It runs off its
own RC oscillator for added reliability. There are two
timers that offer necessary delays on power-up. One is
the Oscillator Start-up Timer (OST), intended to keep
the chip in Reset until the crystal oscillator is stable.
The other is the Power-up Timer (PWRT) which
provides a fixed delay on power-up only, designed to
keep the part in Reset while the power supply
stabilizes. With these two timers on-chip, most
applications need no external Reset circuitry.
Sleep mode is designed to offer a very low current
power-down mode. The user can wake-up from Sleep
through external Reset, Watchdog Timer wake-up, or
through an interrupt. Several oscillator options are also
made available to allow the part to fit the application.
The RC oscillator option saves system cost, while the
LP crystal option saves power. A set of configuration
bits is used to select various options.
24.1 Configuration Bits
The configuration bits can be programmed (read as ‘0’)
or left unprogrammed (read as ‘1’), to select various
device configurations. These bits are mapped, starting
at program memory location 300000h.
The user will note that address 300000h is beyond the
user program memory space. In fact, it belongs to the
configuration memory space (300000h through
3FFFFFh) which can only be accessed using table
reads and table writes.
Programming the Configuration registers is done in a
manner similar to programming the Flash memory. The
EECON1 register WR bit starts a self-timed write to the
Configuration register. In normal operation mode, a
TBLWT instruction, with the TBLPTR pointed to the
Configuration register, sets up the address and the
data for the Configuration register write. Setting the WR
bit starts a long write to the Configuration register. The
Configuration registers are written a byte at a time. To
write or erase a configuration cell, a TBLWT instruction
can write a ‘1’ or a ‘0’ into the cell.
TABLE 24-1: CONFIGURATION BITS AND DEVICE IDS
File Name
Bit 7 Bit 6
Bit 5
Bit 4 Bit 3 Bit 2
Bit 1
Bit 0
Default/
Unprogrammed
Value
300001h CONFIG1H —
— OSCSEN — FOSC3 FOSC2 FOSC1 FOSC0
300002h CONFIG2L —
—
—
—
BORV1 BORV0
BOR PWRTEN
300003h CONFIG2H —
—
300004h⁽¹⁾ CONFIG3L WAIT
—
300005h CONFIG3H MCLRE —
— WDTPS3 WDTPS2 WDTPS1 WDTPS0 WDTEN
—
—
—
—
PM1
PM0
—
—
—
— ECCPMX⁽¹⁾ CCP2MX
300006h CONFIG4L DEBUG —
—
—
—
LVP
—
STVREN
300008h CONFIG5L —
—
—
—
CP3⁽²⁾
CP2
CP1
CP0
300009h CONFIG5H CPD
CPB
—
30000Ah CONFIG6L —
—
—
—
—
—
— WRT3⁽²⁾ WRT2
—
WRT1
—
WRT0
30000Bh CONFIG6H WRTD WRTB
30000Ch CONFIG7L —
—
WRTC
—
—
—
—
—
— EBTR3⁽²⁾ EBTR2 EBTR1
—
EBTR0
30000Dh CONFIG7H — EBTRB
—
—
—
—
—
—
3FFFFEh DEVID1
DEV2 DEV1 DEV0 REV4 REV3 REV2
REV1
REV0
3FFFFFh DEVID2
DEV10 DEV9 DEV8 DEV7 DEV6 DEV5
DEV4
DEV3
Legend:
Note 1:
2:
3:
x = unknown, u = unchanged, – = unimplemented. Shaded cells are unimplemented, read as ‘0’.
Unimplemented in PIC18F6525/6621 devices; maintain this bit set.
Unimplemented in PIC18FX525 devices; maintain this bit set.
See Register 24-13 for DEVID1 values.
--1- 1111
---- 1111
---1 1111
1--- --11
1--- --11
1--- -1-1
---- 1111
11-- ----
---- 1111
111- ----
---- 1111
-1-- ----
(Note 3)
0000 1010
 2003-2013 Microchip Technology Inc.
DS39612C-page 259