PIC18F6525_13 Datasheet, PDF (116/400 Pages) Microchip Technology – 64/80-Pin High-Performance, 64-Kbyte Enhanced Flash Microcontrollers with A/D

PIC18F6525/6621/8525/8621
TABLE 10-9: PORTE FUNCTIONS
Name
Bit# Buffer Type
Function
RE0/AD8/RD/P2D bit 0 ST/TTL⁽¹⁾ Input/output port pin, address/data bit 8, read control for Parallel Slave
Port or Enhanced PWM 2 output P2D
For RD (PSP Control mode):
1 = Not a read operation
0 = Read operation, reads PORTD register (if chip selected)
RE1/AD9/WR/P2C bit 1
ST/TTL⁽¹⁾
Input/output port pin, address/data bit 9, write control for Parallel Slave
Port or Enhanced PWM 2 output P2C
For WR (PSP Control mode):
1 = Not a write operation
0 = Write operation, writes PORTD register (if chip selected)
RE2/AD10/CS/P2B bit 2
RE3/AD11/P3C⁽²⁾
bit 3
RE4/AD12/P3B⁽²⁾
bit 4
RE5/AD13/P1C⁽²⁾
bit 5
RE6/AD14/P1B⁽²⁾
bit 6
RE7/AD15/
ECCP2⁽³⁾/P2A⁽³⁾
bit 7
ST/TTL⁽¹⁾
ST/TTL⁽¹⁾
ST/TTL⁽¹⁾
ST/TTL⁽¹⁾
ST/TTL⁽¹⁾
ST/TTL⁽¹⁾
Input/output port pin, address/data bit 10, chip select control for
Parallel Slave Port or Enhanced PWM 2 output P2B
For CS (PSP Control mode):
1 = Device is not selected
0 = Device is selected
Input/output port pin, address/data bit 11 or Enhanced PWM 3
output P3C.
Input/output port pin, address/data bit 12 or Enhanced PWM 3
output P3B.
Input/output port pin, address/data bit 13 or Enhanced PWM 1
output P1C.
Input/output port pin, address/data bit 14 or Enhanced PWM 1
output P1B.
Input/output port pin, address/data bit 15, Enhanced Capture 2 input/
Compare 2 output/PWM 2 output or Enhanced PWM 2 output P2A.
Legend: ST = Schmitt Trigger input, TTL = TTL input
Note 1: Input buffers are Schmitt Triggers when in I/O or CCP/ECCP modes and TTL buffers when in System Bus
or PSP Control modes.
2: Valid for all PIC18F6525/6621 devices and PIC18F8525/8621 devices when ECCPMX is set. Alternate
assignments for P1B/P1C/P3B/P3C are RH7, RH6, RH5 and RH4, respectively.
3: Valid for all PIC18F6525/6621 devices and PIC18F8525/8621 devices in Microcontroller mode when
CCP2MX is not set. RC1 is the default assignment for ECCP2/P2A for all devices in Microcontroller mode
when CCP2MX is set; RB3 is the alternate assignment for PIC18F8525/8621 devices in operating modes
except Microcontroller mode when CCP2MX is not set.
TABLE 10-10: SUMMARY OF REGISTERS ASSOCIATED WITH PORTE
Name
Bit 7 Bit 6 Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on:
POR, BOR
Value on
all other
Resets
TRISE
PORTE Data Direction Control Register
1111 1111 1111 1111
PORTE
Read PORTE pin/Write PORTE Data Latch
xxxx xxxx uuuu uuuu
LATE
Read PORTE Data Latch/Write PORTE Data Latch
MEMCON⁽¹⁾ EBDIS — WAIT1 WAIT0
—
—
PSPCON⁽²⁾ IBF OBF IBOV PSPMODE —
—
WM1
—
WM0
—
xxxx xxxx
0-00 --00
0000 ----
uuuu uuuu
0000 --00
0000 ----
Legend: x = unknown, u = unchanged, — = unimplemented, read as ‘0’. Shaded cells are not used by PORTE.
Note 1: This register is unused on PIC18F6525/6621 devices and reads as ‘0’.
2: Enabled only in Microcontroller mode for PIC18F8525/8621 devices.
DS39612C-page 116
 2003-2013 Microchip Technology Inc.