PIC18F44J50-I Datasheet, PDF (95/562 Pages) Microchip Technology – 28/44-Pin, Low-Power, High-Performance USB Microcontrollers

PIC18F46J50 FAMILY
TABLE 6-4: REGISTER FILE SUMMARY (PIC18F46J50 FAMILY) (CONTINUED)
File Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on Details
POR, BOR on Page:
RPINR3
RPINR2
RPINR1
RPOR24⁽⁵⁾
RPOR23⁽⁵⁾
RPOR22⁽⁵⁾
RPOR21⁽⁵⁾
RPOR20⁽⁵⁾
RPOR19⁽⁵⁾
RPOR18
RPOR17
RPOR13
RPOR12
RPOR11
RPOR10
RPOR9
RPOR8
RPOR7
RPOR6
RPOR5
RPOR4
RPOR3
RPOR2
RPOR1
RPOR0
Legend:
Note 1:
2:
3:
4:
5:
6:
7:
—
—
—
Input Function INT3 to Input Pin Mapping Bits
---1 1111 76, 156
—
—
—
Input Function INT2 to Input Pin Mapping Bits
---1 1111 76
—
—
—
Input Function INT1 to Input Pin Mapping Bits
---1 1111 76, 156
—
—
—
Remappable Pin RP24 Output Signal Select Bits
---0 0000 76, 168
—
—
—
Remappable Pin RP23 Output Signal Select Bits
---0 0000 76, 167
—
—
—
Remappable Pin RP22 Output Signal Select Bits
---0 0000 76, 167
—
—
—
Remappable Pin RP21 Output Signal Select Bits
---0 0000 76, 167
—
—
—
Remappable Pin RP20 Output Signal Select Bits
---0 0000 76, 166
—
—
—
Remappable Pin RP19 Output Signal Select Bits
---0 0000 76, 166
—
—
—
Remappable Pin RP18 Output Signal Select Bits
---0 0000 76, 166
—
—
—
Remappable Pin RP17 Output Signal Select Bits
---0 0000 76, 165
—
—
—
Remappable Pin RP13 Output Signal Select Bits
---0 0000 76, 165
—
—
—
Remappable Pin RP12 Output Signal Select Bits
---0 0000 76, 165
—
—
—
Remappable Pin RP11 Output Signal Select Bits
---0 0000 76, 164
—
—
—
Remappable Pin RP10 Output Signal Select Bits
---0 0000 76, 164
—
—
—
Remappable Pin RP9 Output Signal Select Bits
---0 0000 76, 164
—
—
—
Remappable Pin RP8 Output Signal Select Bits
---0 0000 76, 163
—
—
—
Remappable Pin RP7 Output Signal Select Bits
---0 0000 76, 163
—
—
—
Remappable Pin RP6 Output Signal Select Bits
---0 0000 76, 163
—
—
—
Remappable Pin RP5 Output Signal Select Bits
---0 0000 76, 162
—
—
—
Remappable Pin RP4 Output Signal Select Bits
---0 0000 76, 162
—
—
—
Remappable Pin RP3 Output Signal Select Bits
---0 0000 76, 162
—
—
—
Remappable Pin RP2 Output Signal Select Bits
---0 0000 76, 161
—
—
—
Remappable Pin RP1 Output Signal Select Bits
---0 0000 76, 161
—
—
—
Remappable Pin RP0 Output Signal Select Bits
---0 0000 76, 161
x = unknown, u = unchanged, - = unimplemented, q = value depends on condition, r = reserved. Bold indicates shared access SFRs.
Bit 21 of the PC is only available in Serial Programming (SP) modes.
Reset value is ‘0’ when Two-Speed Start-up is enabled and ‘1’ if disabled.
The SSPxMSK registers are only accessible when SSPxCON2<3:0> = 1001.
Alternate names and definitions for these bits when the MSSP module is operating in I²C™ Slave mode. See Section 19.5.3.2 “Address
Masking Modes” for details.
These bits and/or registers are only available on 44-pin devices; otherwise, they are unimplemented and read as ‘0’. Reset values are
shown for 44-pin devices.
The PMADDRH/PMDOUT1H and PMADDRL/PMDOUT1L register pairs share the same physical registers and addresses, but have
different functions determined by the module’s operating mode. See Section 11.1.2 “Data Registers” for more information.
The TRISA6 and TRISA7 bits are only implemented when the pins are not configured for primary oscillator functions.
 2011 Microchip Technology Inc.
DS39931D-page 95