ATMEGA8U2_14 Datasheet, PDF (248/310 Pages) ATMEL Corporation – 125 Powerful Instructions – Most Single Clock Cycle Execution

7799D–AVR–11/10
ATmega8U2/16U2/32U2
Table 25-4. Fuse High Byte
Fuse High Byte Bit No Description
Default Value : 0xD9
DWEN⁽⁴⁾
7
Enable debugWIRE (and disable
Reset capability
1 (unprogrammed, debugWIRE
disabled)
RSTDSBL
6
Disable Reset (pin can be used as
general purpose I/O)
1 (unprogrammed, Reset
enabled)
SPIEN⁽¹⁾
WDTON⁽³⁾
5
Enable Serial Program and Data
Downloading
4
Watchdog Timer always ON
0 (programmed, SPI prog.
enabled)
1 (unprogrammed)⁽³⁾
EESAVE
3
EEPROM memory is preserved
through the Chip Erase
1 (unprogrammed, EEPROM
not preserved)
BOOTSZ1
2
Select Boot Size (see Table 25-9 for
details)
0 (programmed)⁽²⁾
BOOTSZ0
1
Select Boot Size (see Table 25-9 for
details)
0 (programmed)⁽²⁾
BOOTRST
0
Select Bootloader Address as Reset 1 (unprogrammed, Reset
Vector
vector @0x0000)
Note: 1. The SPIEN Fuse is not accessible in serial programming mode.
2. The default value of BOOTSZ1..0 results in maximum Boot Size. See Table 23-8 on page 239
for details.
3. See “WDTCSR – Watchdog Timer Control Register” on page 56 for details.
4. Never ship a product with the DWEN Fuse programmed regardless of the setting of Lock bits
and RSTDSBL Fuse. A programmed DWEN Fuse enables some parts of the clock system to
be running in all sleep modes. This may increase the power consumption.
Table 25-5. Fuse Low Byte
Fuse Low Byte
CKDIV8⁽⁴⁾
CKOUT⁽³⁾
SUT1
SUT0
CKSEL3
CKSEL2
CKSEL1
CKSEL0
Bit No
7
6
5
4
3
2
1
0
Description
Divide clock by 8
Clock output
Select start-up time
Select start-up time
Select Clock source
Select Clock source
Select Clock source
Select Clock source
Default Value : 0x5E
0 (programmed)
1 (unprogrammed)
0 (programmed)⁽¹⁾
1 (unprogrammed)⁽¹⁾
1 (unprogrammed)⁽²⁾
1 (unprogrammed)⁽²⁾
1 (unprogrammed)⁽²⁾
0 (programmed)⁽²⁾
Note: 1. The default value of SUT1..0 results in maximum start-up time for the default clock source.
See “System and Reset Characteristics” on page 267 for details.
2. The default setting of CKSEL3..0 results in External crystal Oscillator 8MHz. See Table 8-1 on
page 29 for details.
3. The CKOUT Fuse allow the system clock to be output on PORTC7. See “Clock Output Buffer”
on page 35 for details.
4. See “System Clock Prescaler” on page 35 for details.
The status of the Fuse bits is not affected by Chip Erase. Note that the Fuse bits are locked if
Lock bit1 (LB1) is programmed. Program the Fuse bits before programming the Lock bits.
248