MC68HC908EY16 Datasheet, PDF (243/278 Pages) Motorola, Inc – Microcontrollers

DC Electrical Characteristics
Characteristic⁽¹⁾
Symbol
Min
Typ⁽²⁾
Max
Unit
V_DD + V_DDA supply current
Run^(4),(5)
Wait^{(5), (6)}
Stop (LVI off) @ 25°C⁽⁷⁾
Stop (LVI on) @ 25°C
Stop (LVI off), –40°C to 135°C
Stop (LVI on), –40°C to 135°C
—
18
25
mA
—
5.2
7.0
mA
I_DD
—
0.83
2.00
µA
—
0.19
0.24
mA
—
3.0
30
µA
—
0.19
0.30
mA
I/O ports Hi-Z leakage current⁽⁸⁾
I_IL
–1
—
+1
µA
Input current – RST, OSC1
I_In
–1
—
+1
µA
Capacitance
Ports (as input or output)
C_Out
—
C_In
—
—
—
12
8
pF
POR rearm voltage⁽⁹⁾
V_POR
0
—
100
mV
POR reset voltage⁽¹⁰⁾
V_POR
0
700
800
mV
POR rise time ramp rate
R_POR
0.035
—
—
V/ms
Monitor mode entry voltage
V_TST
V_DD+ 3.5
V_DD+ 4.5
V
Low-voltage inhibit reset, trip falling voltage⁽¹¹⁾
V_TRIPF
3.90
4.30
4.50
V
Low-voltage inhibit reset, trip rising voltage⁽¹²⁾
V_TRIPR
4.00
4.40
4.60
V
Low-voltage inhibit reset/recover hysteresis⁽¹³⁾
V_HYS
—
0.09
—
V
Pullup resistor — PTA0–PTA6/SS⁽¹⁴⁾, IRQ, RST
R_PU
24
—
48
kΩ
1. V_DD = 5.5 Vdc to 4.5 Vdc, V_SS = 0 Vdc, T_A = –40°C to +135°C, unless otherwise noted
2. Typical values reflect average measurements at midpoint of voltage range, 25°C only.
3. Some disturbance of the ADC accuracy is possible during any injection event and is dependent on board layout and power
supply decoupling.
4. Run (operating) I_DD measured using internal oscillator at its 32-MHz rate. V_DD = 5.5 Vdc. All inputs 0.2 V from rail. No dc
loads. Less than 100 pF on all outputs. All ports configured as inputs. Measured with all modules enabled.
5. All measurements taken with LVI enabled.
6. Wait I_DD measured using internal oscillator at its 1-MHz rate. All inputs 0.2 V from rail; no dc loads; less than 100 pF on all
outputs. All ports configured as inputs.
7. Stop I_DD is measured with no port pin sourcing current; all modules are disabled. OSCSTOPEN option is not selected.
8. Pullups and pulldowns are disabled.
9. Maximum is highest voltage that power-on reset (POR) is guaranteed.
10. Maximum is highest voltage that POR is possible.
11. These values assume the LVI is operating in 5-V mode (i.e. LVI5OR3 bit is set to 1).
For 3-V mode (LVI5OR3 = 0), values become Min: 2.45, Typ: 2.60, Max: 2.80
12. These values assume the LVI is operating in 5-V mode (i.e. LVI5OR3 bit is set to 1).
For 3-V mode (LVI5OR3 = 0), values become Min: 2.55, Typ: 2.66, Max: 2.80
13. These values assume the LVI is operating in 5-V mode (i.e. LVI5OR3 bit is set to 1).
For 3-V mode (LVI5OR3 = 0), values become Typ: 60
14. PTA0–PTA4 pullup resistors are for interrupts only and are only enabled when the keyboard is in use.
MC68HC908EY16 • MC68HC908EY8 Data Sheet, Rev. 10
Freescale Semiconductor
243