PIC18F2331_07 Datasheet, PDF (344/400 Pages) Microchip Technology – 28/40/44-Pin Enhanced Flash Microcontrollers with nanoWatt Technology, High Performance PWM and A/D

PIC18F2331/2431/4331/4431
25.2 DC Characteristics: Power-Down and Supply Current
PIC18F2331/2431/4331/4431 (Industrial, Extended)
PIC18LF2331/2431/4331/4431 (Industrial) (Continued)
PIC18LF2331/2431/4331/4431
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
PIC18F2331/2431/4331/4431
(Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Param
No.
Device
Typ Max Units
Conditions
Supply Current (IDD)^(2,3)
PIC18LF2X31/4X31 150 250 μA
-40°C
150 250 μA
160 250 μA
+25°C
+85°C
VDD = 2.0V
PIC18LF2X31/4X31 340 350 μA
300 350 μA
280 350 μA
-40°C
+25°C
+85°C
VDD = 3.0V
FOSC = 1 MHZ
(PRI_RUN,
EC oscillator)
All devices 0.72 1.0 mA
-40°C
0.63 1.0 mA
+25°C
VDD = 5.0V
0.57 1.0 mA
+85°C
PIC18LF2X31/4X31 440 600 μA
450 600 μA
460 600 μA
-40°C
+25°C
+85°C
VDD = 2.0V
PIC18LF2X31/4X31 0.80 1.0 mA
0.78 1.0 mA
0.77 1.0 mA
-40°C
+25°C
+85°C
VDD = 3.0V
FOSC = 4 MHz
(PRI_RUN,
EC oscillator)
All devices 1.6 2.0 mA
-40°C
1.5 2.0 mA
+25°C
VDD = 5.0V
1.5 2.0 mA
+85°C
All devices 9.5 12 mA
-40°C
9.7 12 mA
9.9 12 mA
All devices 11.9 15 mA
12.1 15 mA
+25°C
+85°C
-40°C
+25°C
VDD = 4.2V
VDD = 5.0V
FOSC = 40 MHZ
(PRI_RUN,
EC oscillator)
12.3 15 mA
+85°C
Legend:
Note 1:
2:
3:
4:
Shading of rows is to assist in readability of the table.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS, and all features that add delta
current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated
by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.
Standard, low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
DS39616C-page 342
Preliminary
© 2007 Microchip Technology Inc.