PIC24EP256GU810-I Datasheet, PDF (289/622 Pages) Electronic Film Capacitors, Inc. – 16-Bit Microcontrollers and Digital Signal Controllers with High-Speed PWM, USB and Advanced Analog

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814
15.2 Output Compare Control Registers
REGISTER 15-1: OCxCON1: OUTPUT COMPARE x CONTROL REGISTER 1
U-0
—
bit 15
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
—
OCSIDL
OCTSEL<2:0>
ENFLTC
R/W-0
ENFLTB
bit 8
R/W-0
ENFLTA
bit 7
R/W-0, HSC R/W-0, HSC R/W-0, HSC R/W-0
OCFLTC
OCFLTB
OCFLTA TRIGMODE
R/W-0
R/W-0
OCM<2:0>
R/W-0
bit 0
Legend:
R = Readable bit
-n = Value at POR
HCS = Hardware Settable/Clearable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-14
bit 13
bit 12-10
bit 9
bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
Unimplemented: Read as ‘0’
OCSIDL: Stop Output Compare x in Idle Mode Control bit
1 = Output Compare x Halts in CPU Idle mode
0 = Output Compare x continues to operate in CPU Idle mode
OCTSEL<2:0>: Output Compare x Clock Select bits
111 = Peripheral clock (FP)
110 = Reserved
101 = Reserved
100 = Clock source of T1CLK is the clock source of OCx (only the synchronous clock is supported)
011 = Clock source of T5CLK is the clock source of OCx
010 = Clock source of T4CLK is the clock source of OCx
001 = Clock source of T3CLK is the clock source of OCx
000 = Clock source of T2CLK is the clock source of OCx
ENFLTC: Fault C Input Enable bit
1 = Output Compare Fault C input (OCFC) is enabled
0 = Output Compare Fault C input (OCFC) is disabled
ENFLTB: Fault B Input Enable bit
1 = Output Compare Fault B input (OCFB) is enabled
0 = Output Compare Fault B input (OCFB) is disabled
ENFLTA: Fault A Input Enable bit
1 = Output Compare Fault A input (OCFA) is enabled
0 = Output Compare Fault A input (OCFA) is disabled
OCFLTC: PWM Fault C Condition Status bit
1 = PWM Fault C condition on OCFC pin has occurred
0 = No PWM Fault C condition on OCFC pin has occurred
OCFLTB: PWM Fault B Condition Status bit
1 = PWM Fault B condition on OCFB pin has occurred
0 = No PWM Fault B condition on OCFB pin has occurred
OCFLTA: PWM Fault A Condition Status bit
1 = PWM Fault A condition on OCFA pin has occurred
0 = No PWM Fault A condition on OCFA pin has occurred
TRIGMODE: Trigger Status Mode Select bit
1 = TRIGSTAT (OCxCON2<6>) is cleared when OCxRS = OCxTMR or in software
0 = TRIGSTAT is cleared only by software
Note 1: OCxR and OCxRS are double-buffered in PWM mode only.
 2009-2012 Microchip Technology Inc.
DS70616G-page 289