PIC24EP256GU810-I Datasheet, PDF (182/622 Pages) Electronic Film Capacitors, Inc. – 16-Bit Microcontrollers and Digital Signal Controllers with High-Speed PWM, USB and Advanced Analog

dsPIC33EPXXX(GP/MC/MU)806/810/814 and PIC24EPXXX(GP/GU)810/814
9.3 Oscillator Control Registers
REGISTER 9-1: OSCCON: OSCILLATOR CONTROL REGISTER^(1,3)
U-0
—
bit 15
R-0
R-0
R-0
U-0
R/W-y
COSC<2:0>
—
R/W-y
NOSC<2:0>⁽²⁾
R/W-y
bit 8
R/W-0
R/W-0
R-0
U-0
R/C-0
CLKLOCK
IOLOCK
LOCK
—
CF
bit 7
U-0
R/W-0
R/W-0
—
LPOSCEN OSWEN
bit 0
Legend:
R = Readable bit
-n = Value at POR
y = Value Set from Configuration bits on POR
C = Clearable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
bit 14-12
bit 11
bit 10-8
bit 7
bit 6
bit 5
bit 4
Unimplemented: Read as ‘0’
COSC<2:0>: Current Oscillator Selection bits (read-only)
111 = Fast RC Oscillator (FRC) with Divide-by-N
110 = Fast RC Oscillator (FRC) with Divide-by-16
101 = Low-Power RC Oscillator (LPRC)
100 = Secondary Oscillator (SOSC)
011 = Primary Oscillator (XT, HS, EC) with PLL
010 = Primary Oscillator (XT, HS, EC)
001 = Fast RC Oscillator (FRC) with Divide-by-N and PLL
000 = Fast RC Oscillator (FRC)
Unimplemented: Read as ‘0’
NOSC<2:0>: New Oscillator Selection bits⁽²⁾
111 = Fast RC Oscillator (FRC) with Divide-by-N
110 = Fast RC Oscillator (FRC) with Divide-by-16
101 = Low-Power RC Oscillator (LPRC)
100 = Secondary Oscillator (SOSC)
011 = Primary Oscillator (XT, HS, EC) with PLL
010 = Primary Oscillator (XT, HS, EC)
001 = Fast RC Oscillator (FRC) with Divide-by-N and PLL
000 = Fast RC Oscillator (FRC)
CLKLOCK: Clock Lock Enable bit
1 = If (FCKSM0 = 1), then clock and PLL configurations are locked
If (FCKSM0 = 0), then clock and PLL configurations may be modified
0 = Clock and PLL selections are not locked, configurations may be modified
IOLOCK: I/O Lock Enable bit
1 = I/O lock is active
0 = I/O lock is not active
LOCK: PLL Lock Status bit (read-only)
1 = Indicates that PLL is in lock or PLL start-up timer is satisfied
0 = Indicates that PLL is out of lock, start-up timer is in progress or PLL is disabled
Unimplemented: Read as ‘0’
Note 1:
2:
3:
Writes to this register require an unlock sequence. Refer to Section 7. “Oscillator” (DS70580) in the
“dsPIC33E/PIC24E Family Reference Manual” (available from the Microchip web site) for details.
Direct clock switches between any Primary Oscillator mode with PLL and FRCPLL mode are not permit-
ted. This applies to clock switches in either direction. In these instances, the application must switch to
FRC mode as a transition clock source between the two PLL modes.
This register resets only on a Power-on Reset (POR).
DS70616G-page 182
 2009-2012 Microchip Technology Inc.