M1A3P1000-1PQ208M Datasheet, PDF (99/212 Pages) Microsemi Corporation – Military ProASIC3/EL Low Power Flash FPGAs with Flash*Freeze Technology

Military ProASIC3/EL Low Power Flash FPGAs
SSTL3 Class I
Stub-Speed Terminated Logic for 3.3 V memory bus standard (JESD8-8). Military ProASIC3E devices
support Class I. This provides a differential amplifier input buffer and a push-pull output buffer.
Table 2-151 • Minimum and Maximum DC Input and Output Levels
SSTL3 Class I
Drive
Strength
VIL
Min.
V
Max.
V
V_IH
Min.
V
Max.
V
VOL
Max.
V
VOH
Min.
V
I_OL I_OH
mA mA
I_OSL
Max.
mA³
I_OSH
Max.
mA³
I_IL1 I_IH2
µA⁴ µA⁴
14 mA
–0.3 VREF – 0.2 VREF + 0.2 3.6 0.7 VCCI – 1.1 14 14 51
54 15 15
Notes:
1. I_IL is the input leakage current per I/O pin over recommended operating conditions where –0.3 V < VIN < VIL.
2. II_H is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is
larger when operating outside recommended ranges.
3. Currents are measured at 100°C junction temperature and maximum voltage.
4. Currents are measured at 125°C junction temperature.
VTT
SSTL3
Class I ₅₀
Test Point
25
30 pF
Figure 2-24 • AC Loading
Table 2-152 • AC Waveforms, Measuring Points, and Capacitive Loads
Input Low (V)
Input High (V)
Measuring
Point* (V)
VREF (typ.) (V) VTT (typ.) (V)
VREF – 0.2
VREF + 0.2
1.5
1.5
1.485
Note: *Measuring point = V_trip. See Table 2-28 on page 2-27 for a complete table of trip points.
Timing Characteristics
C_LOAD (pF)
30
Table 2-153 • SSTL3 Class I
Military-Case Conditions: T_J = 125°C, Worst-Case VCC = 1.14 V,
Worst-Case VCCI = 3.0 V, VREF = 1.5 V
Applicable to Pro I/Os for A3PE600L and A3PE3000L Only
Speed
Grade
Std.
t_DOUT
0.80
t_DP
2.29
t_DIN
0.05
t_PY
2.00
t_EOUT
0.52
t_ZL
2.32
t_ZH
t_LZ t_HZ t_ZLS
1.82 – – 2.32
t_ZHS
1.82
Units
ns
–1
0.68 1.95 0.05 1.71 0.44 1.98 1.55 – – 1.98 1.55
ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-5 on page 2-8 for derating values.
Table 2-154 • SSTL3 Class I
Military-Case Conditions: T_J = 125°C, VCC = 1.425 V,
Worst-Case VCCI = 3.0 V, VREF = 1.5 V
Applicable to Pro I/Os for A3PE600L and A3PE3000L Only
Speed
Grade
Std.
t_DOUT
0.61
t_DP
2.15
t_DIN
0.04
t_PY
1.77
t_EOUT
0.40
t_ZL
2.17
t_ZH
t_LZ t_HZ t_ZLS
1.70 – – 2.17
t_ZHS
1.70
Units
ns
–1
0.52 1.83 0.03 1.51 0.34 1.84 1.45 – – 1.84 1.45
ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-5 on page 2-8 for derating values.
Revision 3
2- 85