M1A3P1000-1PQ208M Datasheet, PDF (65/212 Pages) Microsemi Corporation – Military ProASIC3/EL Low Power Flash FPGAs with Flash*Freeze Technology

Military ProASIC3/EL Low Power Flash FPGAs
2.5 V LVCMOS
Low-Voltage CMOS for 2.5 V is an extension of the LVCMOS standard (JESD8-5) used for general-
purpose 2.5 V applications. It uses a 5 V–tolerant input buffer and push-pull output buffer.
Table 2-69 • Minimum and Maximum DC Input and Output Levels
Applicable to Pro I/Os for A3PE600L and A3PE3000L Only
2.5 V LVCMOS
Drive Strength
VIL
Min.
V
Max.
V
VIH
Min.
V
Max.
V
VOL
Max.
V
VOH
Min.
V
I_OL I_OH
mA mA
I_OSL
Max.
mA³
I_OSH
Max.
mA³
I_IL1 I_IH2
µA⁴ µA⁴
4 mA
–0.3 0.7
1.7
3.6
0.7
1.7 4 4
16
18
15 15
8 mA
–0.3 0.7
1.7
3.6
0.7
1.7 8 8
32
37
15 15
12 mA
–0.3 0.7
1.7
3.6
0.7
1.7 12 12
65
74
15 15
16 mA
–0.3 0.7
1.7
3.6
0.7
1.7 16 16
83
87
15 15
24 mA
–0.3 0.7
1.7
3.6
0.7
1.7 24 24
169
124
15 15
Notes:
1. I_IL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL.
2. I_IH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is
larger when operating outside recommended ranges
3. Currents are measured at 100°C junction temperature and maximum voltage.
4. Currents are measured at 125°C junction temperature.
5. Software default selection highlighted in gray.
Table 2-70 • Minimum and Maximum DC Input and Output Levels
Applicable to Advanced I/O Banks
2.5 V LVCMOS
Drive Strength
VIL
Min.
V
Max.
V
VIH
Min.
V
Max.
V
VOL
Max.
V
VOH
Min.
V
I_OL I_OH
mA mA
I_OSL
Max.
mA³
I_OSH
Max.
mA³
I_IL1 I_IH2
µA⁴ µA⁴
2 mA
–0.3 0.7
1.7
2.7
0.7
1.7 2 2
16
18
15 15
4 mA
–0.3 0.7
1.7
2.7
0.7
1.7 4 4
16
18
15 15
6 mA
–0.3 0.7
1.7
2.7
0.7
1.7 6 6
32
37
15 15
8 mA
–0.3 0.7
1.7
2.7
0.7
1.7 8 8
32
37
15 15
12 mA
–0.3 0.7
1.7
2.7
0.7
1.7 12 12
65
74
15 15
16 mA
–0.3 0.7
1.7
2.7
0.7
1.7 16 16
83
87
15 15
24 mA
–0.3 0.7
1.7
2.7
0.7
1.7 24 24
169
124
15 15
Notes:
1. I_IL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL.
2. I_IH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is
larger when operating outside recommended ranges
3. Currents are measured at 100°C junction temperature and maximum voltage.
4. Currents are measured at 125°C junction temperature.
5. Software default selection highlighted in gray.
Revision 3
2- 51