M1A3P1000-1PQ208M Datasheet, PDF (94/212 Pages) Microsemi Corporation – Military ProASIC3/EL Low Power Flash FPGAs with Flash*Freeze Technology

Military ProASIC3/EL DC and Switching Characteristics
HSTL Class I
High-Speed Transceiver Logic is a general-purpose high-speed 1.5 V bus standard (EIA/JESD8-6).
Military ProASIC3E devices support Class I. This provides a differential amplifier input buffer and a push-
pull output buffer.
Table 2-135 • Minimum and Maximum DC Input and Output Levels
HSTL Class I
VIL
Drive
Strength
Min.
V
Max.
V
VIH
Min.
V
Max.
V
VOL
Max.
V
V_OH
Min.
V
I_OL I_OH
mA mA
I_OSL
Max.
mA³
I_OSH
Max.
mA³
I_IL1 I_IH2
µA⁴ µA⁴
8 mA
–0.3 VREF – 0.1 VREF + 0.1 3.6
0.4 VCCI – 0.4 8 8 32
39 15 15
Notes:
1. I_IL is the input leakage current per I/O pin over recommended operating conditions where –0.3 V < VIN < VIL.
2. II_H is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is
larger when operating outside recommended ranges.
3. Currents are measured at 100°C junction temperature and maximum voltage.
4. Currents are measured at 125°C junction temperature.
V_TT
HSTL
Class I ₅₀
Test Point
20 pF
Figure 2-20 • AC Loading
Table 2-136 • AC Waveforms, Measuring Points, and Capacitive Loads
Input Low (V)
Measuring Point*
Input High (V)
(V)
VREF (typ.) (V)
VTT (typ.) (V)
VREF – 0.1
VREF + 0.1
0.75
0.75
0.75
Note: *Measuring point = V_trip. See Table 2-28 on page 2-27 for a complete table of trip points.
Timing Characteristics
C_LOAD (pF)
20
Table 2-137 • HSTL Class I
Military-Case Conditions: T_J = 125°C, Worst-Case VCC = 1.14 V,
Worst-Case VCCI = 1.4 V, VREF = 0.75 V
Applicable to Pro I/Os for A3PE600L and A3PE3000L Only
Speed
Grade
Std.
t_DOUT
0.80
t_DP
3.15
t_DIN
0.05
t_PY
2.76
t_EOUT
0.52
t_ZL
3.20
t_ZH
t_LZ t_HZ t_ZLS
3.11 – – 5.41
t_ZHS
5.32
Units
ns
–1
0.68 2.68 0.05 2.34 0.44 2.73 2.65 –
– 4.60 4.52
ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-5 on page 2-8 for derating values.
Table 2-138 • HSTL Class I
Military-Case Conditions: T_J = 125°C, VCC = 1.425 V,
Worst-Case VCCI = 1.4 V, VREF = 0.75 V
Applicable to Pro I/Os for A3PE600L and A3PE3000L Only
Speed
Grade
Std.
t_DOUT
0.61
t_DP
3.02
t_DIN
0.04
t_PY
2.52
t_EOUT
0.40
t_ZL
3.05
t_ZH
t_LZ t_HZ t_ZLS
3.00 – – 4.51
t_ZHS
4.46
Units
ns
–1
0.52 2.57 0.03 2.14 0.34 2.59 2.55 – – 3.84 3.79
ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-5 on page 2-8 for derating values.
2-80
Revision 3