M1A3P1000-1PQ208M Datasheet, PDF (71/212 Pages) Microsemi Corporation – Military ProASIC3/EL Low Power Flash FPGAs with Flash*Freeze Technology

Military ProASIC3/EL Low Power Flash FPGAs
1.8 V LVCMOS
Low-voltage CMOS for 1.8 V is an extension of the LVCMOS standard (JESD8-5) used for general-
purpose 1.8 V applications. It uses a 1.8 V input buffer and a push-pull output buffer.
Table 2-81 • Minimum and Maximum DC Input and Output Levels
Applicable to Pro I/Os for A3PE600L and A3PE3000L Only
1.8 V
LVCMOS
Drive
Strength
VIL
Min.
V
Max.
V
VIH
Min.
V
Max.
V
VOL
Max.
V
VOH
Min.
V
I_OL I_OH
mA mA
I_OSL
Max.
mA³
I_OSH
Max.
mA³
I_IL1 I_IH2
µA⁴ µA⁴
2 mA
–0.3 0.35 * VCCI 0.65 * VCCI 3.6 0.45 VCCI – 0.45 2 2
9
11
15 15
4 mA
–0.3 0.35 * VCCI 0.65 * VCCI 3.6 0.45 VCCI – 0.45 4 4
17
22
15 15
6 mA
–0.3 0.35 * VCCI 0.65 * VCCI 3.6 0.45 VCCI – 0.45 6 6
35
44
15 15
8 mA
–0.3 0.35 * VCCI 0.65 * VCCI 3.6 0.45 VCCI – 0.45 8 8
45
51
15 15
12 mA
–0.3 0.35 * VCCI 0.65 * VCCI 3.6 0.45 VCCI – 0.45 12 12
91
74
15 15
16 mA
–0.3 0.35 * VCCI 0.65 * VCCI 3.6 0.45 VCCI – 0.45 16 16
91
74
15 15
Notes:
1. I_IL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL.
2. I_IH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is
larger when operating outside recommended ranges
3. Currents are measured at 100°C junction temperature and maximum voltage.
4. Currents are measured at 125°C junction temperature.
5. Software default selection highlighted in gray.
Table 2-82 • Minimum and Maximum DC Input and Output Levels
Applicable to Advanced I/O Banks
1.8 V
LVCMOS
Drive
Strength
Min.
V
VIL
Max.
V
VIH
Min.
V
Max.
V
VOL
Max.
V
V_OH
Min.
V
I_OL I_OH
mA mA
I_OSL
Max.
mA³
I_OSH
Max.
mA³
I_IL1 I_IH2
µA⁴ µA⁴
2 mA
–0.3 0.35 * VCCI 0.65 * VCCI 1.9 0.45 VCCI – 0.45 2 2 9
11 15 15
4 mA
–0.3 0.35 * VCCI 0.65 * VCCI 1.9 0.45 VCCI – 0.45 4 4 17
22 15 15
6 mA
–0.3 0.35 * VCCI 0.65 * VCCI 1.9 0.45 VCCI – 0.45 6 6 35
44 15 15
8 mA
–0.3 0.35 * VCCI 0.65 * VCCI 1.9 0.45 VCCI – 0.45 8 8 45
51 15 15
12 mA
–0.3 0.35 * VCCI 0.65 * VCCI 1.9 0.45 VCCI – 0.45 12 12 91
74 15 15
16 mA
–0.3 0.35 * VCCI 0.65 * VCCI 1.9 0.45 VCCI – 0.45 16 16 91
74 15 15
Notes:
1. I_IL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL.
2. I_IH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is
larger when operating outside recommended ranges
3. Currents are measured at 100°C junction temperature and maximum voltage.
4. Currents are measured at 125°C junction temperature.
5. Software default selection highlighted in gray.
Revision 3
2- 57