M1A3P1000-1PQ208M Datasheet, PDF (206/212 Pages) Microsemi Corporation – Military ProASIC3/EL Low Power Flash FPGAs with Flash*Freeze Technology

Datasheet Information
Revision
Revision 1
(continued)
Changes
Page
All timing and power tables were updated to reflect changes in the software resulting from
characterization and bug fixes (SAR 32394).
2-11
to
2-14
8
In the following tables for A3P250 and A3P1000, the note regarding dynamic power was 2-14,
revised to, "Dynamic Power consumption is given for software default drive strength and _2-14
output slew. Output load is lower than the software default" (SAR 32449).
Table 2-17 • Summary of I/O Output Buffer Power (per pin) – Default I/O Software
Settings 1
Table 2-18 • Summary of I/O Output Buffer Power (per pin) – Default I/O Software
Settings
Values for A3PE600L and A3P250 were added to Table 2-20 • Different Components 2-15,
Contributing to Dynamic Power Consumption in Military ProASIC3 and ProASIC3/EL 2-16
Devices at 1.5 V VCC. Values in the table, and in Table 2-19 • Different Components
Contributing to Dynamic Power Consumption in Military ProASIC3/EL Devices Operating
at 1.2 V VCC, were updated were updated to reflect changes in the software resulting
from characterization and bug fixes (SAR 30528).
Table 2-21 • Different Components Contributing to the Static Power Consumption in 2-16,
Military ProASIC3/EL Devices and the "Total Static Power Consumption—PSTAT" 2-17
calculation were updated to add PDC0 (SAR 32549).
The "Timing Model" was updated (SAR 29793).
2-20
The title of Table 2-28 • Summary of AC Measuring Points was changed from "Summary 2-27
of AC Memory Points" (SAR 32446).
The following note was added to Table 2-30, Table 2-31, and Table 2-31, Summary of I/O
Timing Characteristics (SAR 32449):
"Output delays provided in this table were extracted with an output load indicated in the
Capacitive Load column. For a specific output load, refer to Designer software."
2-28
Resistances and short circuit currents were updated (SARs 29793, 31717):
2-32
Table 2-35 • I/O Output Buffer Maximum Resistances 1 Applicable to Pro I/Os for ^throu
A3PE600L and A3PE3000L Only
gh
Table 2-39 • I/O Short Currents IOSH/IOSL Applicable to Pro I/Os for A3PE600L and ^2-35
A3PE3000L Only (SAR 31717)
Tables for Pro I/Os in the "Single-Ended I/O Characteristics" section (SAR 31717).
The drive strength was changed from 25 mA to 20 mA for 3.3 V and 2.5 V GTL
(SAR 31978). This affects the following tables:
Table 2-24 • Summary of Maximum and Minimum DC Input and Output Levels
Table 2-30 • Summary of I/O Timing Characteristics—Software Default Settings (SAR
32394)
Table 2-31 • Summary of I/O Timing Characteristics—Software Default Settings
Table 2-35 • I/O Output Buffer Maximum Resistances 1 Applicable to Pro I/Os for
A3PE600L and A3PE3000L Only
Table 2-39 • I/O Short Currents IOSH/IOSL Applicable to Pro I/Os for A3PE600L and
A3PE3000L Only
Table 2-119 • Minimum and Maximum DC Input and Output Levels
Table 2-123 • Minimum and Maximum DC Input and Output Levels
2-24
2-28
2-29
2-32
2-35
2-75
2-77
The values in Table 2-38 • I/O Weak Pull-Up/Pull-Down Resistances were revised (SAR 2-34
29793, 28061).
5-2
Revision 3