M1A3P1000-1PQ208M Datasheet, PDF (77/212 Pages) Microsemi Corporation – Military ProASIC3/EL Low Power Flash FPGAs with Flash*Freeze Technology

Military ProASIC3/EL Low Power Flash FPGAs
1.5 V LVCMOS (JESD8-11)
Low-Voltage CMOS for 1.5 V is an extension of the LVCMOS standard (JESD8-5) used for general-
purpose 1.5 V applications. It uses a 1.5 V input buffer and a push-pull output buffer.
Table 2-93 • Minimum and Maximum DC Input and Output Levels
Applicable to Pro I/Os for A3PE600L and A3PE3000L Only
1.5 V
LVCMOS
VIL
Drive
Min.
Strength V
Max.
V
VIH
Min.
V
Max.
V
VOL
Max.
V
VOH
Min.
V
I_OL I_OH
mA mA
I_OSL
Max.
mA³
I_OSH
Max.
mA³
I_IL1 I_IH2
µA⁴ µA⁴
2 mA
–0.3 0.35 * VCCI 0.65 * VCCI 3.6 0.25 * VCCI 0.75 * VCCI 2 2 13
16 15 15
4 mA
–0.3 0.35 * VCCI 0.65 * VCCI 3.6 0.25 * VCCI 0.75 * VCCI 4 4 25
33 15 15
6 mA
–0.3 0.35 * VCCI 0.65 * VCCI 3.6 0.25 * VCCI 0.75 * VCCI 6 6 32
39 15 15
8 mA
–0.3 0.35 * VCCI 0.65 * VCCI 3.6 0.25 * VCCI 0.75 * VCCI 8 8 66
55 15 15
12 mA
–0.3 0.35 * VCCI 0.65 * VCCI 3.6 0.25 * VCCI 0.75 * VCCI 12 12 66
55 15 15
Notes:
1. I_IL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL.
2. I_IH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is
larger when operating outside recommended ranges
3. Currents are measured at 100°C junction temperature and maximum voltage.
4. Currents are measured at 125°C junction temperature.
5. Software default selection highlighted in gray.
Table 2-94 • Minimum and Maximum DC Input and Output Levels
Applicable to Advanced I/O Banks for A3P250 and A3P1000 Only
1.5 V
LVCMOS
Drive
Strength
Min.
V
VIL
Max.
V
VIH
Min.
V
Max.
V
V_OL
Max.
V
VOH
Min.
V
I_OL I_OH
mA mA
I_OSL
Max.
mA³
I_OSH
Max.
mA³
I_IL1 I_IH2
µA⁴ µA⁴
2 mA
–0.3 0.35 * VCCI 0.65 * VCCI 1.575 0.25 * VCCI 0.75 * VCCI 2 2 13
16 15 15
4 mA
–0.3 0.35 * VCCI 0.65 * VCCI 1.575 0.25 * VCCI 0.75 * VCCI 4 4 25
33 15 15
6 mA
–0.3 0.35 * VCCI 0.65 * VCCI 1.575 0.25 * VCCI 0.75 * VCCI 6 6 32
39 15 15
8 mA
–0.3 0.35 * VCCI 0.65 * VCCI 1.575 0.25 * VCCI 0.75 * VCCI 8 8 66
55 15 15
12 mA
–0.3 0.35 * VCCI 0.65 * VCCI 1.575 0.25 * VCCI 0.75 * VCCI 12 12 66
55 15 15
Notes:
1. I_IL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL.
2. I_IH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is
larger when operating outside recommended ranges
3. Currents are measured at 100°C junction temperature and maximum voltage.
4. Currents are measured at 125°C junction temperature.
5. Software default selection highlighted in gray.
Revision 3
2- 63