PIC18F23K22 Datasheet, PDF (433/492 Pages) Microchip Technology – 28/40/44-Pin, Low-Power, High-Performance Microcontrollers with nanoWatt XLP Technology

PIC18(L)F2X/4XK22
27.6 DC Characteristics: Primary Idle Supply Current, PIC18(L)F2X/4XK22
PIC18LF2X/4XK22
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +125°C
PIC18F2X/4XK22
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +125°C
Param
No.
Device Characteristics
Typ Max Units
Conditions
D100
D101
Supply Current (IDD)^(1),(2)
0.025 0.07
0.045 0.10
mA -40°C to +125°C
mA -40°C to +125°C
VDD = 1.8V
VDD = 3.0V
FOSC = 1 MHz
(PRI_IDLE mode,
EC oscillator)
D102
D103
D104
0.04 0.12
0.06 0.15
0.07 0.17
mA -40°C to +125°C
mA -40°C to +125°C
mA -40°C to +125°C
VDD = 1.8V
VDD = 3.0V
VDD = 5.0V
FOSC = 1 MHz
(PRI_IDLE mode,
EC oscillator)
D105
D106
0.45 0.65
0.75 1.10
mA -40°C to +125°C
mA -40°C to +125°C
VDD = 1.8V
VDD = 3.0V
FOSC = 20 MHz
(PRI_IDLEmode,
EC oscillator)
D107
D108
D109
0.5 0.8 mA -40°C to +125°C VDD = 1.8V _{FOSC = 20 MHz}
0.9 1.5 mA -40°C to +125°C VDD = 3.0V ^{(PRI_IDLEmode,}
EC oscillator)
1.1 1.8 mA -40°C to +125°C VDD = 5.0V
D110
FOSC = 64 MHz
2.5 4 mA -40°C to +125°C VDD = 3.0V (PRI_IDLEmode,
EC oscillator)
D111
D112
2.7 4.2 mA -40°C to +125°C VDD = 3.0V FOSC = 64 MHz
(PRI_IDLEmode,
3.3 5.0 mA -40°C to +125°C VDD = 5.0V _{EC oscillator)}
D113
D114
0.40 0.70
0.65 1.10
mA -40°C to +125°C
mA -40°C to +125°C
VDD = 1.8V
VDD = 3.0V
FOSC = 4 MHz
16 MHz Internal
(PRI_IDLE, EC +
PLL)
D115
D116
D117
0.4 0.7 mA -40°C to +125°C VDD = 1.8V FOSC = 4 MHz
0.7 1.2 mA -40°C to +125°C VDD = 3.0V ^{16 MHz Internal}
(PRI_IDLE, EC +
0.9 1.5 mA -40°C to +125°C VDD = 5.0V _PLL)
D118
FOSC = 16 MHz
2.5
4
mA -40°C to +125°C
VDD = 3.0V
64 MHz Internal
(PRI_IDLE, EC +
PLL)
D119
D120
2.7 5.0 mA -40°C to +125°C VDD = 3.0V FOSC = 16 MHz
64 MHz Internal
3.3 6.0 mA -40°C to +125°C VDD = 5.0V ^{(PRI_IDLE, EC +}
PLL)
Note 1:
2:
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as
I/O pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temper-
ature, also have an impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
All I/O pins set as outputs driven to VSS;
MCLR = VDD;
OSC1 = external square wave, from rail-to-rail (PRI_RUN and PRI-IDLE only).
 2010 Microchip Technology Inc.
Preliminary
DS41412B-page 433