PIC24FJ256DA210 Datasheet, PDF (275/408 Pages) Microchip Technology – 64/100-Pin, 16-Bit Flash Microcontrollers with Graphics Controller and USB On-The-Go (OTG)

PIC24FJ256DA210 FAMILY
REGISTER 19-1: PMCON1: EPMP CONTROL REGISTER 1
R/W-0
U-0
R/W-0
R/W-0
R/W-0
U-0
PMPEN
—
PSIDL
ADRMUX1 ADRMUX0
—
bit 15
R/W-0
MODE1
R/W-0
MODE0
bit 8
R/W-0
CSF1
bit 7
R/W-0
CSF0
R/W-0
ALP
R/W-0
ALMODE
U-0
R/W-0
R/W-0
—
BUSKEEP IRQM1
R/W-0
IRQM0
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
bit 14
bit 13
bit 12-11
bit 10
bit 9-8
bit 7-6
bit 5
bit 4
bit 3
bit 2
bit 1-0
PMPEN: Parallel Master Port Enable bit
1 = EPMP is enabled
0 = EPMP is disabled
Unimplemented: Read as ‘0’
PSIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
ADRMUX<1:0>: Address/Data Multiplexing Selection bits
11 = Lower address bits are multiplexed with data bits using 3 address phases
10 = Lower address bits are multiplexed with data bits using 2 address phases
01 = Lower address bits are multiplexed with data bits using 1 address phase
00 = Address and data appear on separate pins
Unimplemented: Read as ‘0’
MODE<1:0>: Parallel Port Mode Select bits
11 = Master mode
10 = Enhanced PSP; pins used are PMRD, PMWR, PMCS, PMD<7:0> and PMA<1:0>
01 = Buffered PSP; pins used are PMRD, PMWR, PMCS and PMD<7:0>
00 = Legacy Parallel Slave Port; PMRD, PMWR, PMCS and PMD<7:0> pins are used
CSF<1:0>: Chip Select Function bits
11 = Reserved
10 = PMA<15> used for Chip Select 2, PMA<14> used for Chip Select 1
01 = PMA<15> used for Chip Select 2, PMCS1 used for Chip Select 1
00 = PMCS2 used for Chip Select 2, PMCS1 used for Chip Select 1
ALP: Address Latch Polarity bit
1 = Active-high (PMALL, PMALH and PMALU)
0 = Active-low (PMALL, PMALH and PMALU)
ALMODE: Address Latch Strobe Mode bit
1 = Enable “smart” address strobes (each address phase is only present if the current access would
cause a different address in the latch than the previous address)
0 = Disable “smart” address strobes
Unimplemented: Read as ‘0’
BUSKEEP: Bus Keeper bit
1 = Data bus keeps its last value when not actively being driven
0 = Data bus is in high-impedance state when not actively being driven
IRQM<1:0>: Interrupt Request Mode bits
11 = Interrupt generated when Read Buffer 3 is read or Write Buffer 3 is written (Buffered PSP mode),
or on a read or write operation when PMA<1:0> = 11 (Addressable PSP mode only)
10 = Reserved
01 = Interrupt generated at the end of a read/write cycle
00 = No interrupt is generated
 2010 Microchip Technology Inc.
DS39969B-page 275