PIC24FJ256DA210 Datasheet, PDF (236/408 Pages) Microchip Technology – 64/100-Pin, 16-Bit Flash Microcontrollers with Graphics Controller and USB On-The-Go (OTG)

PIC24FJ256DA210 FAMILY
REGISTER 17-2: UxSTA: UARTx STATUS AND CONTROL REGISTER
R/W-0
R/W-0
R/W-0
U-0
R/W-0 HC
R/W-0
UTXISEL1 UTXINV⁽¹⁾ UTXISEL0
—
UTXBRK
UTXEN⁽²⁾
bit 15
R-0, HSC
UTXBF
R-1, HSC
TRMT
bit 8
R/W-0
URXISEL1
bit 7
R/W-0
URXISEL0
R/W-0
ADDEN
R-1, HSC
RIDLE
R-0, HSC
PERR
R-0, HSC
FERR
R/C-0, HS
OERR
R-0, HSC
URXDA
bit 0
Legend:
R = Readable bit
-n = Value at POR
HS = Hardware Settable bit
C = Clearable bit
HSC = Hardware Settable/Clearable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
HC = Hardware Clearable bit
bit 15,13
bit 14
bit 12
bit 11
bit 10
bit 9
bit 8
UTXISEL<1:0>: Transmission Interrupt Mode Selection bits
11 = Reserved; do not use
10 = Interrupt when a character is transferred to the Transmit Shift Register (TSR) and as a result, the
transmit buffer becomes empty
01 = Interrupt when the last character is shifted out of the Transmit Shift Register; all transmit
operations are completed
00 = Interrupt when a character is transferred to the Transmit Shift Register (this implies there is at
least one character open in the transmit buffer)
UTXINV: IrDA^® Encoder Transmit Polarity Inversion bit⁽¹⁾
IREN = 0:
1 = UxTX is Idle ‘0’
0 = UxTX is Idle ‘1’
IREN = 1:
1 = UxTX is Idle ‘1’
0 = UxTX is Idle ‘0’
Unimplemented: Read as ‘0’
UTXBRK: Transmit Break bit
1 = Send Sync Break on next transmission – Start bit, followed by twelve ‘0’ bits, followed by Stop bit;
cleared by hardware upon completion
0 = Sync Break transmission is disabled or completed
UTXEN: Transmit Enable bit⁽²⁾
1 = Transmit is enabled, UxTX pin controlled by UARTx
0 = Transmit is disabled, any pending transmission is aborted and the buffer is reset; UxTX pin is
controlled by port.
UTXBF: Transmit Buffer Full Status bit (read-only)
1 = Transmit buffer is full
0 = Transmit buffer is not full, at least one more character can be written
TRMT: Transmit Shift Register Empty bit (read-only)
1 = Transmit Shift Register is empty and transmit buffer is empty (the last transmission has completed)
0 = Transmit Shift Register is not empty, a transmission is in progress or queued
Note 1:
2:
Value of bit only affects the transmit properties of the module when the IrDA^® encoder is enabled
(IREN = 1).
If UARTEN = 1, the peripheral inputs and outputs must be configured to an available RPn/RPIn pin. See
Section 10.4 “Peripheral Pin Select (PPS)” for more information.
DS39969B-page 236
 2010 Microchip Technology Inc.